11.38 11 15909 15908 15906 Baker Drivetrain Transmission Service Parts High Torque Bearing Kit The OEM 34091-85 inner bearing race has been used on Big Twin since 85. The inner primary bearing rides on this race . By design, this race press-fits onto the transmission mainshaft. This system works fine for stock engines. 100 HP+ engines will make this bearing walk on the mainshaft. If it walks inboard, it will damage the main drive gear seal and cause a transmission oil leak. If it walks outboard, it will cause a primary oil leak. The Baker high torque bearing kit eliminates this condition. Kit includes a precision honed bearing and seal. 624105 Fits Big Twin models from 84-06 Anti-Overshift Ratchet Pawl The stock ratchet pawl used from 80-00 utilized a scissor spring that was well known for breaking. Each time an upshift or downshift is made the pawl spring is cycled. After many cycles, the spring breaks. The unfortunate side effect of this failure is the broken spring led going through the transmission gears and destroying the transmission. Any seasoned tech has seen this one. The Baker new ratchet pawl utilizes a rectangular crosssection spring like the 21st century Big Twins. Other improvement is the lever “beak” for overshift protection. 624106 Fits Big Twin 5-speed models 80-99 624105 624106 18430 5-Speed Clutch Release Lever Set A complete chrome-plated clutch release lever set for all 5-speed models from 80-86. This single kit replaces the four separate Original Equipment clutch release arms that the factory has used since 80. Replaces the stock release arm and cable bracket with a stronger, forged release arm and die-cast transmission top cable bracket. Chrome mounting hardware and acorn nut included. 18438 Replaces OEM 37063-90T Note: The installation of this part on 80-82 FXR and FLT models will also require the installation of an OEM 38599-83A clutch cable which is routed along the left side of the engine instead of the right. See the CC cable charts in Section 4 for the different styles of cables available. Chrome Clutch Release Levers Chrome replacement clutch release levers for 4-speed Big Twins. Both levers feature a precision-machined early-style broach for the release finger stud, permitting a wider range of applications than the stock lever. 18430 Fits 4-speed FL and FX models from late 79-86 (repl. OEM 37054-79) Chrome Mousetrap Clutch Release Lever Fits 41-79 Big Twins (68-E79 hand shift only). Also used with CC #19507 Jockey Shift Conversion Kit and Suicide Setup. 19079 Replaces OEMs 37051-36, 3705265 Chrome Transmission Shift Lever This custom part replaces the dull factory transmission shift lever with brilliant chrome. Made of steel. 688723 Fits 5- and 6-speed Big Twins from 97-17(except M8 models) (repl. OEM 33849-97) Chrome Clutch Release Lever For all Big Twins up to early 79 with stock or custom frames, including old-style oil tanks. 19078 Replaces OEMs 37052-65 (late), 37051-36 (early) and 37053-68 with mousetrap eliminator setup Shift Lever Bushings If you’re riding a late 79-86 4-speed FL or FX model, then you’ve probably got a sloppy gear shifter linkage that can be traced to this part or the aluminum shifter arm. Ream your aluminum shifter lever to accept this oversize bushing and restore that ‘good as new’ feel. 20140 Standard size (repl. OEM 3318779)pack of 5 20141 .020" oversize (pack of 5) Clutch Lever Rods and Ends Rods 15906 For use with Mousetrap and Suicide setup (repl. OEM 3691852) 22 3/8"-long 15908 Fits old-style rocker clutch from 36-51 (repl. OEM 36917-36) 18 3/8"-long Clutch Lever Rod End Used on CC #’s 15906 and 15908 clutch rods. 15909 Repl. OEMs 36916-36, 36916-52
RkJQdWJsaXNoZXIy ODQ0NDEw