6.17 for more details check www.custom-chrome-europe.com APPAREL HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT SEATS & TOURING FOOT CONTROLS m.button Another innovation from motogadget: the m.button. It’s a big help - in combination with the new m.unit blue, basic and m.unit v.2 - in reducing ‘cable clutter’ and simplifying wiring harnesses. Integrated into the handlebar tube - or any other adequate location - this tiny cylinder will electrically connect all handlebar instruments, switches and buttons. Using state-of-the-art bus technology, the m.button digitally processes signals and transmits them to the m.unit over a thin cable. The electrical consumers will then be switched inside the m.unit. All control wires are moved into the handlebar. This saves space, weight, labour and time. A ‘must have’ for custom bikes with clean-look handlebars. 690974 mo.Button i.SED 3-In-1 Turn Signal Module • For mounting Indicators with higher wattage than original, indicators on vehicles where the ground is „plus“ but not „minus“ as usual or „DF“ products on vehicles where the indicators ground is switched but not the plus as usual. Note: On some models, the “LED displays” option must be activated PART# FITMENT DESIGN UNIT 912573 14-20 Sportster, 12-17 Dyna, 11-23 Softail, 1423 Touring, 14-23 Trike, 21-23 Sportster RH, 21-23 Pan America i.SED - V 12 Set i.BOS Turn Signal Module • Provides correct function of the control and hazard light, e.g. when using DF versions for Harley Davidson models with Can-Bus. PART# DESIGN UNIT 912572 i.BOS - CL 1 Set CBW1 Can-Bus Resistor • The CBW1 resistor provides a required electrical load for your vehicle, which, if the dip switches are set correctly, will result in no flashing of the accessory flashers in the cockpit. If the accessory indicators fail due to an electronic fault, an error message is immediately displayed in the cockpit. Up to 2 channels can be operated, such as turn signals at the rear left and turn signals at the rear right. The CBW1 can also be used on vehicles with original LED turn signal equipment. • Dimensions: Height = 11mm, Width = 31mm (without straps), Width = 46mm (with tabs), Length = 40mm • Cable length = 200mm with pins • Resistance values: 150 ohms, 200 ohms, 170 ohms, 240 ohms, 300 ohms, 400 ohms, 600 ohms, 1200 ohms PART# UNIT 913218 Each CB2 Position Light Control Box • With few work steps install the CB2 PL CONTROLBOX between the 2in1 indicator and activate a new great safety feature. During the flashing process, the CB2 box switches the position light off and starts only again after the flashing process. Thus, the flashing signal is better perceived in road traffic. • Dimensions: Diameter: 11 mm, Length: 17,5 mm PART# FITMENT UNIT 913219 Not suitable for headlights with position light. Pair Front ABS 12“ Extension Harness • 12“ extension • Allows a simple way to safely lengthen your front end while still having ABS connected properly • 100% Plug-n-Play Fitment Note: ABS Models, Length: 304.8 mm, Unit: Each, Qty.: 1 PART# FITMENT 921795 08-23 Touring, except 17-22 FLHR, 17-18 FLHRC, 18-23 FLHRXS 921796 17-22 FLHR, 17-18 FLHRC, 18-23 FLHRXS
RkJQdWJsaXNoZXIy ODQ0NDEw