6.27 for more details check www.custom-chrome-europe.com APPAREL HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT SEATS & TOURING FOOT CONTROLS Automatic Daytime running light switch • This electronic relay contains 2 power outputs what can drive 60 Watt / each. A daylight sensor detect if the ambience light is dark or bright and the device switch between daytime running light and low beam, depending of the ambience light. The switch time from daytime running light to low beam is immediately for situations when you ride from a bright place in a darker place. The switch time from low beam to daytime running light is adjusted to 3 seconds in order to get the the light sensitivity down against light reflections. You can adjust and store the trigger value of the ambience light in 60 steps. PART# UNIT 914346 Each Flasher Merger The Flasher Merger is connected between the 2 direction indicators and the indicator led in the dashboard or speedo. Two diodes are implemented. The module allows the control of one indicator led for both flashers. The maximum load is 100 mA or 1,2 Watt. The module is waterproof potted what makes it simple to install without the need to wire 2 diodes, insulate it and try to get it waterproofed. Part#: 917975 , Length: 14 mm, Height: 5 mm, Width: 14 mm, Unit: Each , Qty.: 1 Ground Split Terminal Splitter Many electrical problems at the bike result from a bad connection to the minus pole of the battery. The chassis is often in use as minus pole, which is not the best connection due to rust, paint or dirt at the contact screw. The Gnd-Split is a 4 pin divider that can be screwed directly to the minus pole of the battery. It can split up to 4 cables with a maximum size of AWG14. Part#: 919978 , Length: 20 mm, Height: 16 mm, Width: 20 mm, Unit: Each , Qty.: 1 Multi Flasher Plus Relay This is a small flasher controller for pushbuttons in a small package that will fit in every handlebar. This device is controlled via 12 Volt inputs, what make it easier to implement in an existing OEM harness if no minimal wiring is required. An auto cancel function can be activated. It switch off the indicators after a while if no button is pushed. Part#: 917233 , Length: 38 mm, Height: 11 mm, Width: 16 mm, Unit: Each , Qty.: 1 Elektronicbox Version B The B-Box is our response from some clients, who prefer an easy mechanical implementation of the control box in a bike and who don´t take care about a bit bigger size compare to our other devices. The B-Box can be controlled with the standard ignition switch. 8 implemented status led´s allow a fast check while the installation or the adjustment of the different functions. A 20 Ampere inline fuse in the main line is integrated. However, the outputs are short circuit protected and self resetting. • Functions: • Switch - output for parking light / Plate light / speedo etc. • Ignition (with or without side stand switch control) • Starter (with or without neutral switch control) • Headlight with button or switch control • Integrated flasher relay, control with buttons or switches • Brake light with flasher option • Horn Part#: 917230 , Length: 92 mm, Height: 36 mm, Width: 50 mm, Unit: Each , Qty.: 1 Minimal Indicator The minimal indicator is a small microcontroller module and a 3-color LED. The controller drives the different colors of the LED and allows to indicate all necessary functions of your bike with just one LED. Allows to display 2 or 3 events at the same time easily. The small dimensions allows the implementation inside the head light or even in the handle bar. Cleans up your dashboard for a much cooler look. • You can indicate the following functions with one LED: • Flasher left and right • High beam • Neutral • Oil Pressure Part#: 917235 , Length: 38 mm, Height: 11 mm, Width: 16 mm, Unit: Each , Qty.: 1
RkJQdWJsaXNoZXIy ODQ0NDEw