9.63 for more details check www.custom-chrome-europe.com APPAREL HAND CONTROLS LIGHTING ELECTRICAL EXHAUST INTAKE ENGINE GASKETS TRANNY & CLUTCH DRIVELINE WHEELS, TIRES & BRAKES FRAMES FORKS & SHOCKS SHEETMETAL INSTRUMENTS & GAUGES LUBRICANTS & CHEMICALS TOOLS & EQUIPMENT SEATS & TOURING FOOT CONTROLS Andrews Valve Parts for Twin Cam 99-04, Evolution and Shovelhead Motors When installing performance cams, total spring assembly height should be checked before operation. The valve spring collars and springs offered here provide correct total spring assembly height without complicated machining on the heads themselves. High Lift Spring Set Fits Twin Cam 88 and Evolution Big Twin and Sportster motors. When used with the steel upper collars listed above, cam lifts of over .510" can be achieved. Installation does not require machining. Set of 4. 24198 High lift spring set High Lift Spring Set for Shovelheads For 74" and 80" motors. Provide the correct spring pressure for Andrews Shovelhead cams. Installation doesn’t require complicated machining. Set of 4. 24294 High lift spring set for Shovelheads High Lift Upper Collars for Shovelheads When used with high-lift springs, these collars for 74" and 80" motors can accommodate cams of up to .600" lift. Made from T6 aluminum. Set of 4. 24297 High lift upper spring collars for Shovelheads Medium Lift Upper Spring Collars for Shovelheads For 74" and 80" motors and designed to add .060" spring travel to stock springs without other modifications. Simplify the installation of Andrews ‘B’ or ‘#2’ cams in stock Shovelhead motors. Heat-treated steel. Set of 4. 24295 Medium lift upper spring collars for Shovelheads. Low Profile Lower Spring Collars for Shovelheads Low-profile lower spring collars for 74" and 80" motors. Similar to 80-84 OEM collars, but low profile for easier installation of high lift cams. Required if using 80-84 style valve guides which use seals like CC #24347. Made from heattreated steel. Set of 4. 24296 Low profile lower spring collars for Shovelheads. 24296 24295 Manley Valve Spring Lift Kits Increase the amount of valve travel without binding for use with highperformance camshafts with higher-thanstock lift. Kits are packaged with reverse wound springs to reduce harmonics and control spring surge. Most kits are available with titanium collars for ultimate performance, or with steel collars as a lower cost alternative. Kits requiring special machining operations include complete instructions. Valve keepers are not included. Lift Kits for 57-85 Sportster Models Stock-diameter springs with 20% more pressure. Includes steel top collars and uses stock lower collars. Springs 85 lbs. at 1.310", 295 lbs. at .820", bind at .790". 99294 Set of eight valve keepers .465" Lift Kits for Shovelheads Use with stock or Manley thin-stem valves. Kits include springs, upper collars and use stock lower collars. Oversize springs require no machining. Springs 170 lbs. at 1.450", 315 lbs. at .985", bind at .880". 99216 Kit with steel collars for stock stem diameter valves 99295 Set of 8 keepers for CC #99216 99294 Set of 8 keepers for CC #99219 .650" Lift Kits for Shovelheads Titanium top collars with steel lower collars and special interference fit trisprings. 180 lbs. at 1.600", 365 lbs. at 1.100", 415 lbs. at .950", bind at .850". 99295 Set of 8 keepers for CC #99225 kit 99294 Set of 8 keepers for CC #99226 kit 41516 5/16" pilot for CC #99226 Lift Kits for Evolution and Twin Cam 88 Engines Fit Big Twin engines from L84-04, 86-03XL. No machining required, steel or titanium top collars used with stock lower collars. Springs 180 lbs. at 1.800", 360 lbs. at 1.250", 400 lbs. at 1.150", bind at 1.020". 99227 Kit with steel collars (.550" lift) 699240 Kit with steel collars (.600" lift) 99296 Set of eight keepers. Replaces OEM 18229-83 High Performance Ovate Wire Beehive Valve Spring kits by Kibblewhite Kibblewhite springs are made from super clean chrome silicon wire. All springs are shot peened and treated for maximum fatigue life. Beehive springs reduce total valvetrain mass. Kits work with mild cams up to .630” lift. Kits include beehive valve springs, upper collars and lower collars. Kits for Evolution Big Twin models 8499, Sportster models 86-03 and Twin Cam models 99-04 with 5/16” Valve Stems 622239 .630” valve lift OK 175lb. seat pressure and 365lbs at 0.630" lift 622240 .600” valve lift OK 175lb. seat pressure and 355lbs. at 0.600" lift Kits for Twin Cam models 05-16, Sportster models 04-19 and Buell XB9 models 03-10 with 7mm Valve Stems 622241 .600” valve lift OK 175lb. seat pressure and 355lbs. at 0.600" lift 622242 .630” valve lift OK 175lb. seat pressure and 365lbs at 0.630" lift Manley Performance Valve Spring Kits for Twin Cam Engines 05-17 Manley offers two proven valve springs kits that are unequalled in the industry. For stock to .600" lift applications they use single ovate wire, conical design. And for stock to .650" lift, they use true dual reverse wound chrome silicon alloy design. These kits require no head work or machining for installation, and fit all Twin Cam engines with triple keepers from 05-17. 699242 Conical springs with steel collars for up to .600" lift 699243 Conical springs with titanium collars for up to .600" lift
RkJQdWJsaXNoZXIy ODQ0NDEw