CCE Edition Forty Eight | Update by BMG

ELECTRICAL APPAREL SEATS & TOURING HANDLEBARS & RISERS HAND CONTROLS, GRIPS & MIRRORS FOOT PEGS & CABLES INSTRUMENTS & LIGHTING LICENSE PLATES EXHAUST INTAKE COVERS ENGINE TRANNY, CLUTCH & DRIVELINE BRAKES & CHASSIS SHEETMETAL LUBRICANTS & TOOLS UD.105 for more details check www.custom-chrome-europe.com Flasher Merger The Flasher Merger is connected between the 2 direction indicators and the indicator led in the dashboard or speedo. Two diodes are implemented. The module allow the control of one indicator led for both flashers. The maximum load is 100 mA or 1,2 Watt. The modul is waterproof potted what makes it simple to install without the need to wire 2 diodes, insulate it and try to get it waterproof. 917975 Color: Black, Material: ABS, Length mm: 14.0mm, Unit: Each, Qty.: 1.0 Multi Flasher C Have you changed your oem indicators against led devices and still have some trouble with a far too high flasher frequency at the indicators? Have you already tried some different load equalizers without success? Then this device is the solution for you. The Multi Flasher C (The C stands for constant frequency) convert any flasher frequency or even a permanent switched output of the OEM flasher relay to 90 flashes / minute. Just connect the red cable to plus 12 Volt ignition, the black cable to ground / chassis, the thin input cables to the two outputs of the flasher relay in your bike and the thick output cables to your indicators. That´s it. Please note that this module can not convert the flasher frequency of the indicator in your dashboard if you have a CAN bus bike. The CAN bus system can generate an error message in some bikes. In this case is the Vari Load the better solution. 917234 Color: Black, Material: ABS, Length mm: 38.0mm, Unit: Each, Qty.: 1.0 Minimal Indicator The minimal indicator is a small microcontroller module and a 3 color led. The controller drives the different colors of the led and and allows to indicate all necessary functions of your bike with just one led. Allows to display 2 or 3 events at the same time easily. The small dimensions allows the implementation inside the head light or even in the handle bar. Cleans up your dashboard for a much cooler look. You can indicate the following functions with one led: • Flasher left and right • High beam • Neutral • Oil Pressure 917235 Color: Black, Material: ABS, Length mm: 38.0mm, Unit: Each, Qty.: 1.0 Touch 2 Switch 2-Channel Relay This electronic relay have 2 independent channels. Each output can drive 70 Watt. The small size allow an installation in the handlebar or in the headlight. You can switch different loads with a push button. Two different inputs allow to control each output with the switch button, no matter if the button is wired to ground or to + 12 Volt. The Touch 2 Swictch module can also be use as a standard toggle switch relay. Just wire the thin brown input cable direct to ground and the thin blue cinput able direct to + 12 Volt.That´s it. Now the module toggle between output 1 and output 2 if you press the button what is wired to the thin violet cable. • Inputs for non-locking push-button switches in separate mode and for locking switches if the channels are linked together. • You can use very thin cables for the connection between the buttons and the module • 2 independent channels, what can be linked together in order to increase the maximum load to 120 Watt. • The small dimensions allow an implementation in the most handle bars. • The module can also work as voltage inverter. • Push-button switch (not latching) with connection to chassis or to + 12 Volt 919976 Material: ABS, Length mm: 38.0mm, Unit: Each, Qty.: 1.0 917974 Color: Black, Material: ABS, Length mm: 38.0mm, Unit: Each, Qty.: 1.0 Marker Light X Box Marker lights at motorbikes are allowed since some years years and it is a big safety plus, cause the bike is easier to recognize from other traffic. Many manufacturers had developed flasher indicator / marker light combinations. However, the contrast of the direction indicators is very low in some combinations due to the high brightness of the marker light. Our Marker Light X module switches off the marker light in the moment when you switch on the direction indicator at one side. This increase the contrast of the flashers and they are easier to recognize from the other traffic. The implementation of the module is very easy and it fit in the most handle bars due to it´s small dimensions.