dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 16 See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 1506 LOWERING KIT •Lowers the height of your Sportster S by 25 mm (1”) •Made of steel with a black powdercoated finish •Easy installation which doesn’t require a modification to your suspension; no shock compression tool is required •Comes with installation instructions PART # DESCRIPTION 1304-1084 For 21-23 RH1250 S LOWERING KITS •Made of steel with a black powdercoated finish •Easy installation which doesn’t require a modification to your suspension •No shock compression tool is required •Comes with installation instructions NOTE: Operation of centerstand can only be done by 2 people after the installation of the 2” lowering kit. Caution when operating the kickstand is required. PART # DESCRIPTION 1304-1088 2” lowering kit PART # DESCRIPTION 1304-1089 1” lowering kit REAR LOWERING KITS •Made of CNC-machined billet aluminum •Available in a black finish •Lower bike 3/4”, 1” or 1 3/8” NOTE: Rear lowering kits are not to be used in conjunction with “shorty” shocks or “low-profile” shocks. NOTE: Not for use on models with “soft” saddlebags. PART # DESCRIPTION FOR 09-23 FLHT/FLHR/FLHX/FLTR MODELS W/ OEM SHOCKS (INCLUDING HAND-ADJUSTABLE COIL-OVER SHOCKS) 1304-08751 Black PART # DESCRIPTION FOR 09-23 FLHT/FLHR/FLHX/FLTR W/ OEM SHOCKS (EXCEPT OEM HAND-ADJUSTABLE COIL-OVER SHOCKS 1304-0878 Black PART # DESCRIPTION FOR 09-16 FLHT/FLHR/FLTR W/ OEM SHOCKS (EXCEPT OEM HAND-ADJUSTABLE COIL-OVER SHOCKS) 1304-07041 Black 1 Not for use with coil-over adjustable shocks. REAR SHOCK LOWERING BRACKET KIT •Make the motorcycle much easier to get off the side stand and gives more rider control over the motorcycle with its lower center of gravity •Lower your bike 1” leaving adequate room for stock tire-to-fender clearance; designed to retain the use of the stock rubber shock boot •CNC-machined with a black finish •Easy to install in approximately 30 minutes with common tools and includes instructions and hardware NOTE: Rear lowering kit is not to be used in conjunction with “shorty” shocks or “low-profile” shocks. PART # DESCRIPTION 1304-0703 For 02-23 FLHT/FLHR/FLTR models with Original Equipment H-D Air Adjustable Touring Shocks or OEM H-D Premium Ride Hand and Air-Adjustable Touring Shocks (except FLHX/FLHRC/ FLHRS/LOWS and H-D FL Trikes) (models already lowered may use this kit with minimal loads) PART # DESCRIPTION 1304-10861 For 02-17 VRSC/VRSCDX/VRSCF PART # DESCRIPTION 1304-10872 For 04-22 XL 883/1200 (except RH Sportster) 1 Kit includes spring deflection limiters. 2 Requires spring deflection limiters PART #1313-0228. LOWERING KITS •Suitable for use with the Cult-Werk rear fender “Racing” •Kit includes a pair of spacers that mount between the lower shock absorber mounting bolt to place the shock absorbers at an angle and the bike is about 35mm lower as a result •Pieces are CNC-lasered and black powdercoated •If rear axle covers (not original) were subsequently installed on the motorcycle, they must be modified somewhat 1304-0875 1304-0704 FOR 21-23 RA1250/1250S PAN AMERICA
RkJQdWJsaXNoZXIy ODQ0NDEw