dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 4 See OLDBOOK For Early Model Applications DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. All part numbers in BLUE are new for 2024. 437 O2 SENSOR BUNG ADAPTER KIT •Reduces 18 mm exhaust bungs to 12 mm for 10-19 models •Includes extension wire to allow the front sensor to reach the new installation location •Kit includes two adapters, extension wire, wire connectors and instructions PART # DESCRIPTION 1861-0594 O2 sensor bung adapter kit O2 SENSORS •Precision manufactured with a ceramic body made of stabilized zirconium dioxide, surface coated with gas-permeable platinum electrodes and a porous ceramic to help prevent erosion due to contamination and particulates in the exhaust gases •Slow reading oxygen sensors can cause a drop in fuel economy of 10-15%, excessive exhaust emissions and poor drivability •Life expectancy of an average oxygen sensor in a properly tuned engine is typically 30.000-50.000 miles •Available in various overall lengths •All sensors meet or exceed OE specifications •Sold each O2 SENSOR HARNESS EXTENSION AND BUNG ADAPTER •Now you can use 09 Dresser exhaust pipes on 10-16 Dresser models •Reduces the 18 mm O2 bungs on 09 models to 12 mm O2 bungs •Uses NAMZ simple Plug-N-Play wiring harness technology; no cutting or splicing required PART # DESCRIPTION 1861-0608 O2 extension harness O2 SENSOR HARNESS EXTENSION AND BUNG ADAPTER •Allows the use of exhaust systems with 18 mm O2 sensor bungs to be used with late model bikes with 12 mm O2 sensors •Reduces the 18 mm O2 bungs to 12 mm O2 bungs used on many 10-20 models •Wiring harness comes pre-assembled with connector pins PART # DESCRIPTION 1861-0789 O2 extension harness PLUG KIT O2 SENSOR BYPASS •Allows you to bypass OEM O2 sensors when changing from the stock exhaust •For 2010-2022 OEM sensor wiring harness PART # DESCRIPTION 2120-1169 For 10-23 OEM sensor wiring harness 18 MM OXYGEN SENSOR KIT •Kit includes two oxygen sensor assemblies, wire harness, two oxygen boss sensor mounts, two splice connectors and five black cable ties •Wire leads measure 31,75 cm (12 1/2”) L PART # DESCRIPTION 1022-0163 For Magneti Marelli EFI models PART # DESCRIPTION 1020-1479 For late-model European spec models w/ active intake and exhaust ACTIVE INTAKE AND EXHAUST ELIMINATOR KIT •Used to avoid setting a diagnostic trouble code when installing some aftermarket air filters and exhaust that require the removal of original equipment active systems; for off-road racing use only 1861-0884 1861-1107 1861-1108 1861-1253 1861-1647 PART # DESCRIPTION LOCATION 12 MM NARROW BAND O2 SENSORS 1861-1647 For 17-23 Touring models Front (gray 4 wire connector, 52”) 1861-1107 For 10-16 Touring models Front (black 4 wire connector, 29”) 1861-1106 For 10-23 Touring models Rear (black 4 wire connector, 29”) 1861-1253 For 18-23 Softail Front and rear (16”) 1861-1363 For 12-17 Softail, Dyna and 12-17 V-Rod Front (17”) 1861-1362 For 12-17 Softail, Dyna and 12-17 V-Rod Rear (21”) 1861-1362 For 14-19 XL Front and rear (21”) PART # DESCRIPTION LOCATION 18 MM NARROW BAND O2SENSORS 1861-0884 For 07-08 Touring, 07-13 Sportster models Front and rear (12,5”) 1861-0884 For 09 Touring models Rear (12,5”) 1861-0885 For 07-11 Softail, 06-11 Dyna models Front and rear (16,25”) 1861-0885 For 09 Touring, 09 V-Rod models Front (16,25”) O2 SENSORS ADAPTOR 1861-1108 12 mm/18 mm -
RkJQdWJsaXNoZXIy ODQ0NDEw