dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. SECTION 5 See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 459 PART # DESCRIPTION HS42/001-K Mikuni-to-CV carb air box adapter w/ three mounting screws 990-605-065 Short idle screw adjuster 990-662-002 Choke cable, for use with Mikuni plastic nut, spring and brass plunger REPLACEMENT PARTS FOR HSR 42/45 CARB KITS PART # DESCRIPTION 1006-0248 HSR4 main jet extension kit HSR4 MAIN JET EXTENSION KIT •Increases amount of fuel to float bowl •Completely submerges main jet within extender, eliminating chance of air bubbles getting through PART # DESCRIPTION 1050-0390 Needle and seat assembly for Mikuni HSR42/45 carburetor NEEDLE AND SEAT ASSEMBLY FOR MIKUNI HSR42/45 CARBURETOR •Replacement needle and seat assembly for HSR42/45 carburetors •Includes needle, seat and O-ring PART # DESCRIPTION KHS-016 HSR42/45 Carb rebuild kit PART # DESCRIPTION KHS-031 HSR48 Carb rebuild kit GENUINE MIKUNI HS CARBURETOR REBUILD KITS •Genuine Mikuni parts properly replaceworn or mistreated components for HSR42/45/48 carburetors •Includes top cover gasket, jet needle E-ring and washer, throttle valve seal, pilot air O-ring, fuel joint O-ring, accelerator pump O-ring, needle valve O-ring, needle valve retainer screw, needle valve assembly, float bowl O-ring/gasket, overflow hose, float bowl screws, accelerator pump rod boot PART # DESCRIPTION 1003-1275 For 00-06 Twin Cam (includes: 45, 48, 50 pilot jets 190,195, 200 main jets; N8EA needle) 1003-1271 For 88-03 XL 883 (includes: 42, 45, 48 pilot jets; 160, 165, 170 main jets; N0KH needle) PART # DESCRIPTION 1003-1274 For 04-06 XL 1200 (includes: 42, 45, 48 pilot jets; 180, 185, 190 main jets; N0KH needle) 1003-1272 For 88-03 XL1200 (includes: 42, 45, 48 pilot jets; 170,175,180,190,195,200 main jets; N0KH needle) CV CARBURETOR REBUILD KITS •NBR rubber material is used on all O-rings and rubber gaskets; NBR has excellent resistance to the ethanol used in today’s fuels •Components included in the kit are based on U.S. models and discretion must be used when attempting to install the kit on a non-U.S. model •All gaskets and O-rings, including intake gaskets before and after the carburetor •Kit includes float bowl, carburetor cap, and accelerator pump screws •Extended fuel mixture screw with spring, washer, and O-ring 990-662-002 990-605-065 HS42/001-K •Float needle valve with FMK tip •Accelerator pump diaphragm spring and boot •Emulsion tube with slide needle •Three main jets and three pilot jets that can be used to tune a stock machine or a modified one •Kit is intended for closed-course racing only KHS-031 KHS-016 •Includes all the parts needed to rebuild HSR42/45 or HSR48 carburetors 1003-1271
RkJQdWJsaXNoZXIy ODQ0NDEw