dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 6 DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 558 ROCKER ARM SHAFT KITS •Shafts are precision-machined from a low alloy nickel, chromium, molybdenum case-hardened steel •Hardware flats on the end of the shafts are held to a 0,0005” parallel tolerance, assuring the rocker is seated in the correct position with the pushrod cup and valve stem tip •PART #0927-0034 includes a stud and nut kit to replace the stock hardware used to secure the rocker shafts PART # DESCRIPTION FOR 17-21 M-EIGHT ENGINES 0927-0034 Rocker arm shafts with hardware kit 0927-0035 Rocker arm shafts only; repl. OEM #17300059A ROCKER ARM SHAFTS •Made from bearing-quality steel and precisioncenterless ground for the perfect fit •Stronger than stock to resist issues from radical cam profiles •Sold in a set of four NOTE: S&S recommends installing rocker stud kit PART #2401-1139 (sold separately) with these rocker arm shafts. PART # DESCRIPTION 0927-0041 For 17-23 M-Eight; repl. OEM #17300059A ROCKER ARM SHAFTS •Sold each or in a set of four PART # DESCRIPTION FOR 99-17 TWIN CAM, 86-22 XL (EXCEPT RH SPORTSTER); REPL. OEM #17611-83 90-4036 Set of 4 0927-0029 Each ROCKER ARM SHAFT •Sold each PART # DESCRIPTION DS-193820 For 99-17 Twin Cam, 86-21 XL (except RH Sportster) and 94-09 Buell (except 1125R) motors; repl. OEM #17611-83 ROCKER ARM BUSHING •Replacement bushing for S&S roller rocker arms •Sold each PART # DESCRIPTION 0927-0030 For S&S standard and roller rocker arms ROCKER ARM BUSHINGS •Manufactured from solid billet bearing bronze bar stock •ID 0,547” •Sold in packs of 8 •Ream to fit PART # DESCRIPTION DS-193821 For 99-17 Twin Cam, 86-21 XL (except RH Sportster); repl. OEM #17428-57 PART # DESCRIPTION 0930-0240 For all 17-23 M-Eight ROCKER SHAFT SHIMS •Quiet your engine by tightening the rocker arm to cylinder head end play clearance •Feuling recommends an ideal side clearance of 0,0035” - 0,005” for optimum rocker arm oil psi and noise reduction •M-Eight cylinder heads also have excessive wear on the rocker arm standoff thrusting surfaces; when the hardened shim is placed on the thrusting side it will assist in reduction of further wear and damage to cylinder head •Includes six 0,003” thick shims, six 0,005” thick shims and six 0,0010” thick shims NOTE: These shims should be installed by a professional; one who can make correct end play measurements and can install and tighten rocker shaft nuts/bolts without damaging shims. 0927-0034 0927-0035 90-4036
RkJQdWJsaXNoZXIy ODQ0NDEw