dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 6 DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 582 HP103 EZ CAMS •Bolt-in cam for 103” and 106” Big Bore Twin Cam motors •Use with stock heads (up to 10,2 compression) and low-restriction intake and exhaust •Great for lighter bikes with strong power from 3500-6000 rpm MR103 EZ CAMS •Bolt-in cam for 103” Twin Cam motors •Use with stock heads and low restriction intake and exhaust •Broad torque curve improves output over stock over the entire rpm range 551 EZ CAMS •Optimized for 88”/96”/103” to 106” Touring bikes with slip-on mufflers and 9,0 to 10,0:1 compression •Best bolt-in cam available for most 05-16 Dressers •Can be used with stock pushrods, springs and lifters •Pulls hard from idle to 4000 rpm 557 EZ CAMS •Designed for Tri-Glides and other heavy bikes needing good bottom and mid-range performance •Bolt-in design 570 EZ CAMS •For 88/95/96/103 cubic-inch engines •Compression ratios below 10:1 •99-04 models require high-lift springs 583 EZ CAMS •Optimized for use as a great overall cam for Softail and Dyna, but can be used in any Big Twin •Provides strong low-end torque and horsepower you can really feel •Strongest from 1500-5000 rpm in a Softail and Dyna application •99-04 models require high-lift springs 585 EZ CAMS •Optimized for 95” to 106” with slip-on mufflers, highflow air filter and 9,0 to 10,5:1 compression •Great results from 3000-6000 rpm •99-04 models require high-lift springs and adjustable pushrods EASY START CAM KITS FOR TWIN CAM (CONT) GRIND OPEN CLOSE DURATION @ 0,053” VALVE LIFT S&S HP103 Intake 20° 49° 249° 0,575” Exhaust 45° 26° 251° 0,575” S&S MR103 Intake 13° 33° 226° 0,585” Exhaust 50° 22° 252° 0,585” S&S 551 Intake 17° 19° 215° 0,550” Exhaust 41° 17° 237° 0,550” S&S 557 Intake 6° 26,5° 212° 0,557” Exhaust 38,8° 12,4° 231° 0,557” S&S 570 Intake 20° 40° 240° 0,570” Exhaust 55° 20° 250° 0,570” S&S 583 Intake 5° 18° 204° 0,583” Exhaust 58° 24° 262° 0,583” S&S 585 Intake 20° 45° 245° 0,585” Exhaust 60° 20° 260° 0,585” PART # DESCRIPTION FOR 07-17 TWIN CAM, 06 DYNA 0925-0446 Chain drive cam kit 0925-0451 Gear drive cam kit PART # DESCRIPTION FOR 99-06 BIG TWIN (EXCEPT 06 DYNA) 0925-0524 Chain drive cam kit 0925-0455 Gear drive cam kit PART # DESCRIPTION FOR 07-17 TWIN CAM, 06 DYNA 0925-0445 Chain drive cam kit 0925-0450 Gear drive cam kit FOR 99-06 BIG TWIN (EXCEPT 06 DYNA) 0925-0523 Chain drive cam kit 0925-0454 Gear drive cam kit PART # DESCRIPTION FOR 07-17 TWIN CAM, 06 DYNA 0925-0444 Chain drive cam kit PART # DESCRIPTION FOR 07-17 TWIN CAM, 06 DYNA 0925-0613 Chain drive cam kit PART # DESCRIPTION FOR 07-17 TWIN CAM, 06 DYNA 0925-0443 Chain drive cam kit 0925-0448 Gear drive cam kit FOR 99-06 BIG TWIN (EXCEPT 06 DYNA) 0925-0521 Chain drive cam kit 0925-0453 Gear drive cam kit PART # DESCRIPTION FOR 07-17 TWIN CAM, 06 DYNA MODELS 0925-0829 Chain drive cam kit 0925-0832 Gear drive cam kit FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0925-1046 Gear drive cam kit PART # DESCRIPTION FOR 07-17 TWIN CAM, 06 DYNA MODELS 0925-0830 Chain drive cam kit FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0925-1053 Gear drive cam w/ inner gears only
RkJQdWJsaXNoZXIy ODQ0NDEw