dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 6 DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 588 CAMS FOR TWIN CAM (CONT) GRIND OPEN CLOSE DURATION @ 0,053” DURATION @ 0,020” VALVE LIFT LIFT TDC 32 SERIES Intake 10° 46° 236° 272° 0,570” 0,131” Exhaust 52° 08° 240° 276° 0,570” 0,120” 37 SERIES Intake 18° 38° 236° 272° 0,510” 0,174” Exhaust 46° 14° 240° 276° 0,510” 0,140” TW48 SERIES Intake 13° 29° 222° 257° 0,548” 0,153” Exhaust 43° 15° 238° 273° 0,548” 0,163” 50 SERIES Intake 20° 48° 248° 283° 0,510” 0,184” Exhaust 54° 18° 252° 287° 0,510” 0,168” 54 SERIES Intake 16° 42° 238° 273° 0,555” 0,165” Exhaust 43° 15° 238° 273° 0,555” 0,158” 55 SERIES Intake 22° 46° 248° 283° 0,550” 0,197” Exhaust 52° 20° 252° 292° 0,550” 0,181” 57 SERIES Intake 18° 38° 236° 270° 0,560” 0,184” Exhaust 46° 14° 240° 274° 0,560” 0,153” 32 SERIES GRIND CAMS •High-lift version of 31G. Much more (+20%) power through rpm range with 10:1+ compression ratio •2800-5800 rpm range 37 SERIES GRIND CAMS •Bolt-in cams •Smooth idle with broad torque band •Run best with low-restriction exhausts (2200-5800 rpm) •Can be used with stock valve springs and tappets •Works well with carbs or fuel injection TW48 SERIES GRIND CAMS •Broad tip cams for baggers with stock motors; max torque at low- and mid-rpm ranges •Use stock springs 50 SERIES GRIND CAMS •Designed for 95”+ motors with 9,25:1 to 9,50:1 compression ratio and stock heads •For lighter bikes •Cams work best at higher rpm of 2500-6000 •Can be used with stock valve springs and tappets 54 SERIES GRIND CAMS •Designed for 96” and 103” motors with up to 10:1 compression ratio •Cams work best at rpm range of 2200-5600 55 SERIES GRIND CAMS •Cams for maximum torque and horsepower at higher rpm ranges (2600-6000+ rpm) •Designed for engines with 9,5:1 compression ratio or higher with 88”-95” •Coil bind must be checked, but stock tappets can be used 57 SERIES GRIND CAMS •Bolt-in broad tip cams; 96”, 103” Limited and 110” CVO engines •Cams work best at rpm range of 2200-5600 PART # DESCRIPTION FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0188 32H chain-drive cam kit PART # DESCRIPTION FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0172 37HG gear-drive cam kit 0925-0115 37H chain-drive cam kit FOR 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) DS199247 37G gear-drive cam kit DS-199180 TW37 chain-drive cam kit PART # DESCRIPTION FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0598 TW48 chain-drive cam kit FOR ALL 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) 0925-1274 TW48 chain-drive cam kit PART # DESCRIPTION FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0117 50H chain-drive cam kit FOR 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) DS-199181 TW50 chain-drive cam kit PART # DESCRIPTION FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0278 54H chain-drive cam kit FOR 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) 0925-0282 TW54 chain-drive cam kit PART # DESCRIPTION FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0118 55H chain-drive cam kit PART # DESCRIPTION FOR ALL 07-17 TWIN CAM AND 06 DYNA GLIDE 0925-0668 57H chain-drive cam kit PART # DESCRIPTION FOR ALL 99-06 TWIN CAM (EXCEPT 06 DYNA GLIDE) 0925-1275 57H chain-drive cam kit
RkJQdWJsaXNoZXIy ODQ0NDEw