dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. SECTION 6 See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 599 PART # DESCRIPTION FOR 17-23 M-EIGHT 0932-0250 W/ Twin Cooled™ engines PART # DESCRIPTION FOR 17-23 M-EIGHT (CONT) 0932-0251 W/ oil-cooled engines OIL PUMP AND CAMPLATE FOR M-EIGHT •Precision-machined from billet aluminum •Independent scavenge sections for the flywheel cavity and the cam chest •Debris screens in both scavenge pickups •Magnet in the cam chest to help prevent debris from entering the oil pump •Increased oil flow capacity on both the feed and scavenge side •Adjustable pressure relief valve can be adjusted with the unit still in the engine •Passage plugs are removable for servicing •Blue anodized finish 0932-0250 PART # DESCRIPTION 0925-1255 For 17-23 M-Eight oil-cooled motors PART # DESCRIPTION 0932-0230 For 17-23 M-Eight Twin-cooled™ motors HP+ OIL PUMP/CAMPLATE KITS FOR M-EIGHT •Increase oil pressure, oil volume, engine oil flow and return oil scavenging •Quieter and smoother engine operation •15-25 °F cooler engine temperatures •15-30 °F cooler oil temperatures •10-30 more psi of oil pressure •Reduces wet sumping, blowby and oily air cleaners •Test results show 2 horsepower gain and 2 ft/lbs of torque gain to the rear wheel on M-Eight •Feuling test results show as much as 50% reduction of engine sump oil level •Includes a billet 6061 aluminum high volume oil pump and Feulings® High Flow billet camplate made from 7075 aluminum; which is 50% harder and stronger than the factory or Feuling OE+ camplates •Increases oil flow and volume by enlarging the oil pump reservoirs and critical oil passages including matching the oil portholes throughout the camplate to the portholes in the engine case which increases engine oil flow to the lifters, piston cooling jets, crankshaft and rod bearings •Oil pumps are bench tested, the relief valve is seated and sealed to a minimum of 30 psi with full pop-off at 55-60 psi •Increased oil volume from the larger gears and properly sized passages along with the pressure relief valve seat and seal from these oil pumps are essential for proper oiling system function •Feuling oil pump and camplate combination eliminates common pressure and scavenge issues associated with the factory oiling systems •Feuling M-Eight oil pumps have the groove machined on the back cover to accept the factory crank bearing seal •Optional Camplate/oil pump fastener kit PART #2401-0993 available separately; see page 607 •PART #0925-1255 has 27% more pressure and scavenge gear volume over stock, 42% more scavenge volume through port sizing, matched passages and holes to the engine case and 68% more oil volume to the crankshaft and connecting rod bearing •PART #0932-0230 has 30% more pressure gear volume over stock, 53% more scavenge gear volume over stock and 42% more scavenge volume with port sizing, matched passages and holes to the engine case NOTE: The M-Eight oil pick up port is on the right side of the engine. Letting the bike idle or warm up on the kickstand will naturally fill the engine case and skew the oil level in the tank. NOTE: Not for 2023 models with 121” VVT motors. 0932-0230
RkJQdWJsaXNoZXIy ODQ0NDEw