dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 6 DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 606 PART # DESCRIPTION 0932-0192 For 17-23 M-Eight HIGH FLOW CAMPLATE FOR M-EIGHT •Increases engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages including the scavenging return holes from the pump to the camplate and into the engine case •Camplate matches the oil portholes on the camplate to the oil holes in the engine case to increase oil flow throughout the engine •Lowers engine temperatures by 15-25 °F and oil running temperature by 15-25 °F when matched with a Feuling HP+ or RS oil pump •7075 billet aluminum construction, which is 50% harder and stronger than the factory cast and Feuling® OE+ camplates •Increases the strength and hardness of the camplate, holding tighter tolerances under temperature and eliminating flexing and the need for bronze bushings •When matched with the Feuling® Race Series Oil Pump, rear wheel power gains of 2 horsepower and 2 ft./lb. of orque can be achieved •For gear or chain drive cams (block-off plate PART #0932-0036 required when using gear drive cams) NOTE: For use ONLY with Feuling HP+ and Race Series M-Eight oil pumps. PART # DESCRIPTION 0932-0193 For 17-23 M-Eight OE+ CAMPLATE FOR M-EIGHT •Feuling® OE+ stock replacement billet camplate is manufactured from 6061 aluminum, providing increased rigidity and machined to Feuling’s high tolerance standards •Direct bolt-in replacement and accepts the factory OEM oil pump only •Blueprinted and matched oil passages to the engine case passages, kidney shapes are designed to maximize flow •Optimizes oil flow to and from the oil pump and in and out of the engine, aiding in reducing oil and engine temps •Tighter cam journal bore tolerance for improved cam fitment •Added cam journal oil groove for cold startup protection and increased cam journal lubrication •Added oil pressure feed holes to front and back of cam journal to prevent excessive thrusting wear •For gear or chain drive cams (block-off plate PART #0932-0036 required when using gear drive cams) NOTE: Not for 2023 models with 121” VVT motors. PART # DESCRIPTION 0932-0268 For 17-23 M-Eight CAMPLATE FOR M-EIGHT •Precision-machined from billet aluminum •Blue anodized finish •For use with S&S or OEM oil pumps •Passage plugs are removable for servicing PART # DESCRIPTION 0925-0914 For 07-17 Twin Cam and 06 Dyna models 0925-09151 For 99-06 Twin Cam models (except 06 Dyna) w/ gear drive cams 1 Accepts 07-16 style oil pumps only. TC3 CAMPLATES FOR TWIN CAM •Precision CNC-machined forged aluminum •Adjustable oil pressure regulator; adjust without removing plate from the engine •Passage plugs are removable for service •Rebuildable bronze pinion shaft bushing in all models and bronze cam bushings in 07-later style NOTE: S&S oil pumps for 99-06 are not compatible with S&S cam support plates for 99-06 engines. All S&S cam support plates are machined for 07 and later-style oil pumps. 0925-0914
RkJQdWJsaXNoZXIy ODQ0NDEw