Parts Europe FatBook by BMG

dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. SECTION 6 See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 607 PART # DESCRIPTION FOR 07-17 TWIN CAM (AND 06 DYNA) 0925-01101, 2 For chain or gear drive cams FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0920-00063 For gear drive cams PART # DESCRIPTION FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) (CONT) 0925-01093, 4 For chain drive cams w/ spring tensioners 0925-04405 Hydraulic tensioner conversion camplate for stock chain drive cams 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 Requires the use of 07-17 style Feuling HP+ or Race Series oil pump PART #s 0932-0023 or 0932-0026. 3 Requires the use of 99-06 style Feuling HP+ or Race Series oil pump PART #s 0932-0018 or 0932-0020. 4 Includes tensioner pins and guide hardware. 5 Requires 07-17 hydraulic chain drive system (tensioners, chains, sprockets and hardware), see Feuling tensioner kit PART #s 0925-1069 or 0925-1070. HIGH FLOW CAMPLATES FOR TWIN CAM •Increase engine oil flow and volume by enlarging the oil pump reservoirs and critical oil passages •Camplate matches the oil port holes throughout the camplate to the portholes in the engine case increasing engine oil flow throughout the engine •25-35 °F cooler engine temperatures and 20-30 °F cooler oil temperatures •Made from 7075 billet aluminum which is 50% harder and stronger than the factory, SE® and other aftermarket camplates •The 7075 increases the strength and hardness of the camplate, holding tighter tolerances under temperature eliminating flexing and the need for bronze bushings •Camplates are pressure tested and pressure relief valve is seated, sealed and set to pop off at 55-60 psi •When matched with the Feuling® Race Series oil pump rear wheel power gains of 3 horsepower and 4 ft/​lbs of torque can be achieved •For use ONLY with the Feuling® oil pumps •Camplates for 99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerances for improved press fit •Bearing and retainer plate hardware is included •Camplates for 07-17 Twin Cam (and 06 Dyna) have tighter cam journal tolerance for improved cam fitment •Added cam journal oil groove for cold startup protection and increased cam journal lubrication •Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear 0925-0440 0925-0110 PART # DESCRIPTION FOR 07-17 TWIN CAM (AND 06 DYNA) 0925-08421, 5 For chain or gear drive cams FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) 0925-08392 For gear drive cams PART # DESCRIPTION FOR 99-06 TWIN CAM (EXCEPT 06 DYNA) (CONT) 0925-08402, 3 For chain drive cams w/ spring tensioners 0925-08414 Hydraulic tensioner conversion camplate for stock chain drive cams 1 Block-off plate PART #0932-0036 required when using gear drive cams. 2 For use with factory or any Twin Cam oil pump with the 99-06 bolt pattern. Compatible with Feuling oil pump PART #s 0932-0018, 0932-0089, 0932-0020. 3 Includes tensioner pins and hardware guide. 4 Requires 07-17 style oil pump, hydraulic chain drive system (tensioners, chains, sprockets and hardware), see Feuling tensioner kits 0925-1069 or 0925-1070. Compatible with Feuling oil pump PART #s 0932-0090, 0932-0023, 0932-0026. 5 For use with factory and or any Twin Cam oil pump with 07-17 bolt pattern; compatible with Feuling oil pump PART #0932-0090, 0932-0023, 0932-0026. OE+ CAMPLATES FOR TWIN CAM •Billet camplates are manufactured from 6061 aluminum providing increased rigidity and machined to Feuling® high tolerance standards •Designed and manufactured to the highest standard of quality with proven Feuling® performance •The pressure relief valve and spring are pre-set, matched and seated by Feuling® with a full pop off pressure of 50-60 psi •Camplates for 99-06 Twin Cam (except 06 Dyna) have tighter cam bearing bore tolerance for improved press fit •Bearing retainer plate and hardware included •Camplate for 07-17 Twin Cam (and 06 Dyna) have tighter cam journal bore tolerance for improved cam fitment •Added cam journal oil groove for cold startup protection and increased cam journal lubrication •Added oil pressure feed holes to front and back of cam journals to prevent excessive thrusting wear 0925-0842 0925-0839 PART # DESCRIPTION 2401-09931 For 17-23 M-Eight engines w/ Feuling high flow camplate and HP+ or Race Series oil pumps (do not use washers with ARP® oil pump bolts) 2401-0127 For 99-17 Twin Cam engines w/ Feuling HP+, Race Series or OE+ camplates and oil pumps 1 Not for use with OE+ camplates/​oil pumps. CAMPLATE/​OIL PUMP FASTENER KITS •Optional kit for Feuling camplates/​oil pumps only •Quality 12-point, heat-treated 8740 chromoly steel bolts with black oxide finish manufactured by ARP® to Feuling’s exact specifications •Precision-rolled threads provide optimum engagement, prevent galling and promote consistent torque loading •Wide, underhead flange design provides even load distribution for optimum sealing of surfaces to prevent leaks •Tensile strength rated at 170.000 psi; superior and stronger than OEM and stronger than grade 8 fasteners •Includes moly assembly lubricant for installation 2401-0127

RkJQdWJsaXNoZXIy ODQ0NDEw