dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL AUDIO, COMMUNICATION & MOUNTS FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 6 DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. See OLDBOOK For Early Model Applications All part numbers in BLUE are new for 2024. 610 HIGH-PERFORMANCE TWIN CAM OIL PUMPS •Helps to reduce oil carryover during high-rpm operation; higher volume helps reduce engine and oil temperatures •53 mm diameter rotors for maximum performance •Gain of 20% oil pressure, 125% pressure volume and 135% scavenge volume over OEM stock TC88 oil pumps •Gain of 16% oil pressure, 66% pressure volume and 100% scavenge volume over OEM stock TC96/103 oil pumps PART # DESCRIPTION 0932-0088 For 07-17 Twin Cam and 06 Dyna models 0932-0087 For all 99-06 Twin Cam (except 06 Dyna models) REPLACEMENT COMPONENTS 0932-0219 Gerotor scavenge for Twin Cam 88” and 96” applications PART # DESCRIPTION REPLACEMENT COMPONENTS (CONT) 0932-0220 Gerotor feed for Twin Cam 88” and 96” applications 0932-0221 Partition plate and O-ring set for 88” Twin Cam applications TC3 OIL PUMP •Three stages for consistent pressure and reliable scavenging •Separate scavenge sections for flywheel cavity and cam chest (no interface) •Screens and magnetic traps help protect the scavenge rotors from debris •Special design allows S&S pumps to tolerate more pinion shaft run-out without damage •Oil pump replacement parts sold separately NOTE: S&S oil pumps for 99-06 are not compatible with S&S cam support plates for 99-06 engines. All S&S cam support plates are machined for 07 and later-style oil pumps. OIL PUMPS PART # DESCRIPTION 0932-01061 For 07-17 Twin Cam and 06 Dyna models 1 Will not fit 00-02 Softails when used with a TC3 cam plate. REPLACEMENT PARTS PART # DESCRIPTION 0932-0209 Debris screen 0935-1014 O-ring, 1,5 mm x 14 mm Viton® (5-pk.) PART # DESCRIPTION 0935-1015 O-ring kit 2401-1048 Screw kit, oil pump, 99-19 Big Twin (1/4” x 20 x 2” SHCS w/ washers) OIL PUMP ASSEMBLY •High-quality replacement cast-aluminum pump body with steel gears and shaft •Raw cast-aluminum finish •Gaskets and seals included PART # DESCRIPTION 0932-0189 For 91-22 XL (except RH Sportster models) OIL PUMP REBUILD KITS •Include everything needed to rebuild Feuling® HP+® and Race Series oil pumps •Kit comes with new O-rings, separator plate and installation instructions PART # DESCRIPTION 0932-0019 For Feuling® oil pump PART #s 0932-0018, 0932-0020 0932-0024 For Feuling® oil pump PART #s 0932-0023, 0932-0026 OIL PUMP REPAIR KITS •Comes with new components that allow you to totally rebuild/rebush most Big Twin and XL oil pumps •Gasket/seal kits are available to complete the job PART # DESCRIPTION MFG. DS-194202 Gasket/bushing kit for 86-90 XL Eastern MC Parts PART # DESCRIPTION MFG. DS-174531 Gasket/seal kit for 91-03 XL James Gasket DS-194202 0932-0019 0932-0106 •High-quality die-cast aluminum body construction, high-strength steel gear construction •Fits both stock and aftermarket cam support plates for seamless installation NOTE: Does not fit Screamin’ Eagle cam plate. 0932-0088 0932-0219 0932-0221
RkJQdWJsaXNoZXIy ODQ0NDEw