dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 6 All part numbers in BLUE are new for the OldBook. See FATBOOK For Late Model Applications 337 DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. PART # DESCRIPTION DS-195007 Idler gear stud kit with bushing kit for 36-69 Big Twin OHV; repl. OEM #s 25791-36, 25785-30A DS-195008 Idler gear stud and bushing kit for 57-85 XL; repl. OEM #s 25787-57, 25597-57 DS-188049 Idler and circuit breaker stud snap rings for 36-69 Big Twin (10-pk.); repl. OEM #25810-15 IDLER GEAR AND CIRCUIT BREAKER BUSHINGS/STUDS •Idler gear bushings/studs •Also work for circuit breakers as noted below DS-188049 DS-195007 PART # DESCRIPTION 0925-0290 For 58-85 XL; repl. OEM #25551-58 CAM GEAR THRUST PLATES •Sold in pairs PART # DESCRIPTION 0925-1333 Cam lock washer; repl. OEM #25550-57A CAM LOCK WASHER •For Big Twin engines with 4”, 4 1/8” or 4 3/8” cylinder bore •Sold each PART # DESCRIPTION DS-193144 For 58-99 Big Twin models; repl. OEM #25550-57 CAM LOCK WASHERS •Sold in 5-packs CAM SHIMS •Available in a set of 10, or in individual sizes in 5-pack PART # DESCRIPTION OEM # FOR 36-99 BIG TWIN DS-1941621 10-piece set (0,050” through 0,095”) - 0925-0288 0,040” (5-pk.) - 0925-0289 0,045” (5-pk.) 25555-48 DS-194163 0,050” (5-pk.) 25550-36 DS-194164 0,055” (5-pk.) 25551-36 DS-194165 0,060” (5-pk.) 25552-36 DS-194166 0,065” (5-pk.) 25553-36 DS-194167 0,070” (5-pk.) 25554-36 DS-194168 0,075” (5-pk.) 25555-36 FOR 32-73 45”; 52-56 K, KH AND KHK; 57-85 XL DS-194070 0,005” for cam gears #1, 3 and 4 (10-pk.) 6770 DS-194071 0,007” for cam gears #1, 3 and 4 (10-pk.) 6769 DS-194072 0,015” for cam gears #1, 3 and 4 (10-pk.) - 0925-0284 0,005” for cam gear #2 (10-pk.) - 0925-0285 0,010” for cam gear #2 (10-pk.) - 0925-0286 0,015” for cam gear #2 (10-pk.) - 1 Sold as a set. PART # DESCRIPTION FOR 93-99 EVOLUTION BIG TWIN STYLE ENGINE 0920-0008 Standard 0920-0009 +0,030” oversize CRANKCASE BREATHER REED VALVES •New-style breather is not dependent on the rotation of the crankshaft to make it open and close; instead, reeds open when pressure in the crankcase becomes greater than pressure in the cam chest, and close when pressure in the cam chest is equal to or greater than pressure in the crankcase •By opening and closing “on demand,” the reed valves automatically compensate for lag time associated with accelerating the mass of air as it is forced out of the crankcase, increasing performance and stopping high-rpm oil carryover in engines with marginal piston ring seal •Installation is fast and simple; no aligning timing marks, and no rotating parts 0920-0008
RkJQdWJsaXNoZXIy ODQ0NDEw