dragspecialties.eu / partseurope.eu WINDSHIELDS & FAIRINGS SADDLEBAGS & LUGGAGE SEATS & SISSY BARS FUEL/AIR SYSTEMS EXHAUST TRANSMISSION, CLUTCH LINE & DRIVELINE ENGINE GASKETS & SEALS LIGHTING & LICENSE PLATES ELECTRICAL HANDLEBARS, CONTROLS & MIRRORS CABLES TANKS & OIL FILTERS BRAKES & BRAKE LINES DASHES & GAUGES FENDERS COVERS, LOCKS & GENERAL FRAMES & SUSPENSION FOOTRESTS & FLOORBOARDS WHEELS & AXLES SECTION 9 All part numbers in BLUE are new for the OldBook. See FATBOOK For Late Model Applications 521 DISCLAIMER: SEE PAGE 5 FOR IMPORTANT INFORMATION REGARDING CERTAIN WARRANTY AND EMISSION CONTROL REGULATION COMPLIANCE AND NOISE REGULATION INFORMATION. COMPLETE BIKE HARNESS •The perfect start for any project bike or OEM model rewire •Complete bike harness w/ starter relay, 3-circuits, self-canceling and run, brake and turn signal module •Works with any stand-alone, Evo or Twin Cam ignition system •Designed to operate with a two-position key switch •Key start switches can be used with a simple wiring modification (ignition system and key switch are not included with this harness) •OEM color-matching harness with 11-second self-canceling turn signal module •Fuse block holds a full size, commonly available and replaceable starter relay and three ATO fuses •A 30-amp circuit breaker is installed and is ready for any regulator/charging system •Oil, neutral, high beam and turn signal indicator wiring •Color-matching handlebar switch wiring, as found on most 96-13 models (except Dresser models) •Part #2120-1178, color-matching handlebar switch wiring, as found on most 96-13 non-glide models •Headlight wiring with headlight socket and terminals •Front turn signal connectors and terminals •Rear fender harness with connectors and terminals •Key switch wiring with ring terminals PASSING LAMP CONTROL HARNESS •Allows the use of passing lamps while the high beam is on •Plug-n-play installation REAR WIRING HARNESSES AND ADAPTERS •Plug-n-play installation •Wiring matches OEM color-coding •Connects to rear taillight circuit board •Made in the U.S.A. •Adapters allow Plug-n-Play connection of 10-20 FLTRX/FLHX OEM harness to models listed •Harnesses and adapters sold separately LED HEADLAMP ADAPTER HARNESS •Required when replacing the stock dual-halogen headlamps with an LED headlamp or any other H4 based headlamp •Sold each HANDLEBAR SWITCH WIRE EXTENSIONS •61 cm (24”) and 122 cm (48”) wire extensions •For cut and solder applications •Wire ends are stripped but left with slugs to prevent fraying HARNESS TURN SIGNAL TAP •Front turn signal tap •For adding additional front turn signals • Plug-n-play PART # DESCRIPTION 2120-0769 Complete harness PART # DESCRIPTION 2120-1178 Complete harness PART # DESCRIPTION 2120-0973 Indicator only PART # DESCRIPTION 2120-1118 For 98 FLHS/FLHT/FLHTC/FLHTCU/ FLHTCUL/FLHTCUSE/FLHTK/ FLHTKL/FLHX/FLHXS/FLHXXX PART # DESCRIPTION WIRING HARNESS 2120-1060 For 97-98 FLHR/FLHTK/FLHX, 96-99 FLST, 97-98 FXD/FXDWG PART # DESCRIPTION WIRING HARNESS ADAPTERS 2120-1058 For 97-98 FLHR/FLHT/ FLTR using a 14-20 style harness 2120-1059 For 97-98 FLHR/FLHT/FLTR using a 10-13 style harness PART # DESCRIPTION 2120-0647 For custom applications PART # DESCRIPTION 2001-1264 H4 adapter for custom applications PART # DESCRIPTION FOR 82-95 MODELS (EXCEPT DRESSER MODELS) 2120-1020 61 cm (24”) extension 2120-1021 122 cm (48”) extension PART # DESCRIPTION 2120-1116 For 96-98 FLHR/FLHT 2120-0647 2001-1264 •Coil wire with ring terminals, tachometer, horn, oil sending unit, brake switch and neutral switch wiring with terminals •4,8 mm (3/16”), 6,4 mm ( 1/4”), 9,5 mm ( 3/8”), and 12,7 mm (1/2”) heat shrink sections included •Heavy gauge 12(+) power and (-) ground wires with terminals for battery connection •PART #2120-0769 has provisions for front and rear turn signals which function as run, brake, turn signal. OEM color matching harness with 11-second self canceling turn signal module •PART #2120-0973 has no turn signal wiring, only indicator wiring 2120-1060 2120-1058 2120-1021 2120-0769
RkJQdWJsaXNoZXIy ODQ0NDEw