Speedo Seats & Luggage- racks Frame Chassis Suspension Forktubes Wheels Brake Fenders Gastanks Motorparts Gaskets Intake Transmission & Driveline Exhaust Electrical & Lights Handlebars, Cables & Mirrors Oil tanks Oil & Chemicals Fasteners Windshields Forward controls, Footpegs Miscellaneous ELECTRICAL - IGNITION, WIRING, STARTERS, REGULATORS & BATTERIES 15 1169 AFTERMARKET PARTS & ACCESSORIES FOR CUSTOM MOTORCYCLES / MOTORCYCLESTOREHOUSE.COM DYNATEK, SHIFT MINDER SYSTEM Offered in two versions, for two and four cylinder applications. Consists of two components, the module and the shift light. The module is adjustable to 64 different RPM settings, with 125 RPM increments between settings. Shift Minder system 902590 Two cyl 4000-11875 RPM 902592 Four cyl 6000-13875 RPM Standard repl. shift light 902593 Standard replacement Custom shift lights Small and lightweight miniature shift lights with a LED light and a color anodized housing to color match it to your bike. 902594 Silver 902599 Blue 902608 Red 902609 Green 902611 Black 902592 902543 DYNATEK, DIGITAL IGNITION SYSTEM Digital adjustable ignition for all 99-06 carbureted Twin Cam and models. A total of 16 programmed advance curves in 3 following groups. A) Stock to slightly modified, B) Heavily modified, C) Extreme modified. 8 different RPM. limiter settings from 5750 to 7500 RPM in steps of 250 RPM. This is all adjustable by 2 knobs on the back. Additonal programming options by PC are available when using the Programming kit. Compatible with stock and Dyna coils. All stock ignition sensors are used. The units will mount in the same place, and use the same connectors as the stock black box it replaces. Note: 902563 and 902564 do not offer PC programmable options. Carb models 902543 99-03 Twin Cam (TC88-2P) 902563 04-06 Twin Cam (TC88-3) 902564 04-05 XL Sportster (DSPT-1) Programming kit for 902543 only 902546 Programming kit (wiring harness only, incl. software dowload information) DYNATEK, DYNA 2000HD The Dyna 2000 modules are used in combination with the OEM HD ignition system. The system must mount externally and lets you control advance curves by using 4 preset modes and the R.P.M. limiter lets you choose from 4 R.P.M. limits from 6000 to 7500. A built-in timing light is used for static timing. Can be wired for dual or single fire operation. 915683 7-pin Cannon connector. Fits 91-95 Softail, Dyna, FXR; 91-93 FLT, XL 915688 Wiring harness adapter for 84-90 H-D models 915690 8-pin Deutsch connector. Fits 96-99 Softail; 96-98 Dyna; 94-98 FLT and 94-97 XL 915683 Custom shift lights 902525 902530 DYNATEK, DYNA-S IGNITION MODULES Dyna-S electronic ignition modules are available for single and dual fire applications. Comes complete with rotor. Both modules can be used for single or dual plugged heads. Fits 70-99 Big Twin (excl. TC) and 71-03 XL Sportster models. A mechanical advance unit must be purchased separately. Dyna coil recommendations: Dyna 5 Ohm for street use, Dyna 3 Ohm for race use. Note: It is recommended to use ignition modules & coils of the same manufacturer. Intermixing different brands may cause premature failure. 902525 Dual fire, mechanical advance 902530 Single fire, mechanical advance Replacement rotors Dyna-S Stock replacement ignition rotors for Dyna-S ignition modules. 902547 Rotor for dual fire 902548 Rotor for single fire 907410 DYNATEK, TACH ADAPTER Used to correct electronic tachometer output when using a Dyna-S single fire module. Note: This adapter cannot be used with Spyke, S&S, Crane or Compu-Fire ignition modules. 907410 Tach adapter DYNA-S MODULES TACH ADAPTER REV LIMITER DYNA SHIFT MINDER DYNA 2000 DYNA PROGRAMMABLE FOR CARB DYNATEK, TWO-STAGE REV LIMITER Controls over-revving and launch RPM. The high limit controls the 5500 to 9250 RPM. The low, 2500 to 6250 launch limit, is used for clean consistent runs. Both are adjustable with 250 RPM increments. Complete with installation instructions. Note: Compatible with carbon core supression spark plug cables only. 936986 Univ. H-D with most inductive electronic ignition systems 936987 07-up fuel injected H-D with a 4-position connector plug on the coil 936987 936986 IGNITION HARNESS NAMZ, STAND ALONE IGNITION HARNESS For use with Twin Cam engines with crank position sensor in combination with an 04-06 OEM style or aftermarket ignition module like Dyna 2000 TC-3, SE, Daytona Twin Tec TC88A ignition modules. 588888 Twin Cam with crank position sensor 588888
RkJQdWJsaXNoZXIy ODQ0NDEw