Speedo Seats & Luggage- racks Frame Chassis Suspension Forktubes Wheels Brake Fenders Gastanks Motorparts Gaskets Intake Transmission & Driveline Exhaust Electrical & Lights Handlebars, Cables & Mirrors Oil tanks Oil & Chemicals Fasteners Windshields Forward controls, Footpegs Miscellaneous BRAKE 07 493 AFTERMARKET PARTS & ACCESSORIES FOR CUSTOM MOTORCYCLES / MOTORCYCLESTOREHOUSE.COM 920808 921823 920807 GOODRIDGE BANJO BOLTS Available in chrome and stainless. Chr. SS Black A) 920838 920839 921867 M10 x 1.00 920840 920844 921868 M10 x 1.25 908797 920794 921425 3/8-24 908798 920793 921424 7/16-24 920809 920810 -- M12 X 1.50 B) 908792 920795 3/8-24. Long, use with 'short neck' banjo C) 920848 920849 M10 x 1.00. Double bolt 920850 920851 M10 x 1.25. Double bolt 908794 920796 3/8-24. Double bolt, for two banjos 908793 -- 7/16-24. Double bolt, for two banjos D) -- 920852 M10 x 1.00. With brakelight switch -- 920853 M10 x 1.25. With brakelight switch -- 920847 3/8-24. With brake light switch -- 920846 7/16-24, with brake light switch E) 920819 Rubber boot only for 920852/53/46/47 switch F) 920868 920869 M10 x 1.00. With bleed nipple -- 920871 M10 x 1.25. With bleed nipple 920872 920873 3/8-24. With bleed nipple G) 920874 920875 M10 x 1.00. Double + bleed nipple -- 920877 M10 x 1.25. Double + bleed nipple GOODRIDGE BANJO FITTINGS Used in combination with Goodridge Build-A-Line brake lines. These fittings are installed on one or both ends of the brake line. Fittings are available in chrome and stainless steel. Chr. SS A) 921800 923800 3/8" (10mm). Short neck (note: use 908792 chrome or 920795 SS longer banjo bolt) 921801 923801 7/16" (11mm). Short neck B) 921802 923802 3/8" (10mm). Straight 921803 923803 7/16" (11mm). Straight 920811 920812 12mm. Straight C) 921804 923804 3/8" (10mm). 20° bend 921805 923805 7/16" (11mm). 20° bend 920813 920814 12mm. 20° bend D) 921806 923806 3/8" (10mm). 45° bend E) 921809 923809 3/8" (10mm). 70° bend F) 921810 923810 3/8" (10mm). 90° bend 921821 - 7/16 (11mm). 90° bend G) 921807 923807 3/8" (10mm). 20° side bend - 923816 3/8" (10mm). 90° side bend H) -- 923808 3/8" (10mm). Short neck, double fitting, straight. (note: use 908792 or 920795 SS longer banjo bolt) I) -- 923815 3/8" (10mm). Short neck, double fitting, 90° (note: use 908792 or 920795 SS longer banjo bolt) GOODRIDGE FITTING SLEEVES & NUTS Replacement brass fitting sleeves and nuts for the Goodridge Build-A-Line brake line nipples. 921823 Fitting sleeves (olives) Chr. SS 920807 920808 Fitting nut E F D G H I A C B 921818 A B C D E F G GOODRIDGE HOSE ENDS Used in combination with Goodridge Build-A-Line brake lines. These fittings are installed on one or both ends of brake lines. Hose end fittings come with female 3/8"-24 AN-3 thread. Chr. SS A) 921811 923811 Straight, hose end B) 921812 923812 45° bend tube, hose end C) 921813 923813 90° bend tube, hose end A B C GOODRIDGE - DIRECT CONNECT - Used in combination with Goodridge Build-A-Line brake lines. These fittings can be installed on caliper, master cylinder or brake tee and then make a direct connection to the Goodridge Build-a-line brake line, without additional adapter fittings, for the cleanest look. Note: Only one of these nipples should be used since it has no swivel head. Using these nipples on both sides would result in a twisted brake line during installation. Chr. SS 921819 923819 M10-1.00 to hose 921820 -- M10-1.25 to hose 921818 923818 3/8-24 inverted flare to hose 921844 921869 3/8-24 straight to convex seat 921844 BRAKE LINE WASHERS Crush washers used in combination with a banjo bolt and banjo fitting. Note: Goodridge manufactured, unless mentioned otherwise. Copper 908777 3/8" (10mm) 908778 7/16" (11mm) 908833 12mm Aluminum 908779 3/8" (10mm) 527203 3/8" (10mm) Gardner-Westcott 908781 7/16" (11mm) 527204 12mm Gardner-Westcott Stat-O-Seal (Aluminum) Aluminum crush washer bonded to a synthetic rubber o-ring. Temp. range -30°C up to 233°C. 920889 3/8" (10mm) 920890 7/16" (11mm) 908779 908777 920889 GOODRIDGE 'BUILD-A-LINE' BRAKE LINES Universal
RkJQdWJsaXNoZXIy ODQ0NDEw