Speedo Seats & Luggage- racks Frame Chassis Suspension Forktubes Wheels Brake Fenders Gastanks Motorparts Gaskets Intake Transmission & Driveline Exhaust Electrical & Lights Handlebars, Cables & Mirrors Oil tanks Oil & Chemicals Fasteners Windshields Forward controls, Footpegs Miscellaneous MOTOR PARTS - LOWER END 10 631 AFTERMARKET PARTS & ACCESSORIES FOR CUSTOM MOTORCYCLES / MOTORCYCLESTOREHOUSE.COM 566108 566109 FEULING, CHAIN GUIDE TOWER & TENSIONER PINS Adapts Feuling kit 566083 oiling system kit and cam plate 566079 to chain drive systems. 566108 99-06 Twin Cam (excl. 2006 Dyna) FEULING, CAM BEARING RETAINER PLATE KIT Includes hardware. Repl. 35060-00. 566109 99-06 Twin Cam (excl. 2006 Dyna) FEULING, CAM PLATE TENSIONER PINS Heat treated chromoly pins. Used when changing Twin Cam chain drive cam support plate or replacing the chain tensioners. 566112 99-06 Twin Cam (excl. 2006 Dyna) 566112 FEULING, BLOCK-OFF PLATES Optional part for gear driven cams. Must be separately ordered when required. Used on cam support plates when using gear drive camshafts. Used to block-off oil holes for the hydraulic chain tensioner system. Fits both stock, Screamin' Eagle and aftermarket cam support plates. 566113 06-17 Dyna; 07-23 Softail; 07-23 Touring 566113 FEULING, OIL PUMP / CAM SUPPORT PLATE FASTENER KIT Optional superior hardware mount kit for the demanding engine builder. 12-point heat treated 8740 chromoly, with black oxide finish. Includes moly assembly lube. 566115 99-17 Twin Cam with Feuling cam support plate & oil pump 566115 S&S, CAM BEARING RETAINER PLATE Heavy duty. Recommended to be used in all gear driven camshaft applications. Note: This cam bearing retainer plate is included in the S&S TC cams installation support kits. 531269 99-06 TCA/B (excl. 2006 Dyna) 531269 CAM CHAINS, TWIN CAM & M8 Replacement cam drive chains for Twin Cam and M8 models. Note that Twin Cam uses a dual (inner & outer chain) and M8 models run a single cam chain. 99-06 TCA/B (excl. 2006 Dyna) 921161 Inner (secondary). Repl. 25607-99 921163 Outer (primary). Repl. 25610-99 06-17 Dyna; 07-17 Softail; 07-16 Touring 921604 Inner (secondary). Repl. 25683-06 921606 Outer (primary). Repl. 25675-06 17-23 M8 Softail, Touring 921606 Repl. 25675-06 921163 921604 FEULING, OIL PUMP PRESSURE RELIEF SPRINGS Used to increase cam support plate pressure relief pop-off pressure. Controls both pop-off pressure and oil flow in the bypass port. Note: Feuling recommends bench testing with the Feuling cam support plate pressure test tool, 566117, to set pop-off pressure to your preference and to ensure correct valve seal and valve operation. 566114 99-17 Twin Cam 566114 FEULING, OIL PUMP PRESSURE RELIEF SPRINGS This spring offers increased oil pump pop-off pressure when compared to the stock spring. This adds seat pressure and increases the overall pop off pressure and gives correct oil flow in the bypass port. Note: Not required for Feuling oil pumps. These are pre set with the proper pop-off and valve seal at the factory. 588057 17-23 M8 588057 S&S, OIL CONTROL VALVE M8 The OEM 62700141 oil control valve (check valve), used on all oil cooled M8 engines in the front right side of the crankcase, regulates the amount of oil flowing to the oil cooler/heads. The stock assembly includes a check ball retainer that is formed steel. Over time this retainer can fatigue and break, causing chips to flow through the oil and cause engine damage. The S&S oil control valve is constructed of 6061 billet aluminum and the check ball retainer is machined from high strength steel for long-lasting durability. Easy and quick to install. 17-23 M8 (excl. Twin Cooled models) 933572 933572 FEULING, OIL PUMP VALVE, SPRING & ROLL PIN KIT Fits M8 oil pumps including OEM and Feuling, Includes steel plunger valve, compression spring and roll pin. Note: Short roll pin fits factory pump housing and longer roll pin fits Feuling pump housing. 18-23 Softail; 17-23 Touring 588055 588055
RkJQdWJsaXNoZXIy ODQ0NDEw