299 V-TWIN TOOLS NEW PRODUCTS ADDED WEEKLY AT MOTORCYCLESTOREHOUSE.COM JIMS, CAM GEAR ALIGNMENT TOOLS Used to remove and install the camshaft gear. You may reposition it on another camshaft with exactly the same timing. Removing the gear and adjusting the present timing by pressing it on in a advanced or retarded position is also possible. 978294 70-99 B.T. (excl. TC) (install tool) 978387 70-99 B.T. (excl. TC) (remove tool) 978294 978387 LOWER END JIMS, CAM BUSHING & BUSHING ALIGNMENT TEST TOOL Used to check correct alignment between the inner cam bearing and outer cam cover bushing within .0003". Any binding of this tool will indicate misalignment of the cam cover bushing and/or the cam cover itself. Note: Use JIMS tool MCS 978292 for line reaming the cam cover bushing. 978293 70-99 B.T. (excl. TC) 978293 JIMS, CAM BUSHING LINE REAMER TOOL Used with disassembled crankcases. Used to line ream the cam cover bushing to the correct size, through the inner cam bearing. This will give a true centerline for the cam. Finished size will be between .0008" and .0015" over the cam journal. Note: See MCS 978293 for JIMS cam bushing & bearing alignment test tool. 978292 70-99 B.T. (excl. TC) 978292 JIMS, B.T. CAM SEAL INSTALLER/REMOVER Used to install and remove cam seal, without removing the cam cover. This tool is very simple to use. Just mount tool in cover, screw in the two removing screws, turn center, and out comes the cam seal. The new seal is pressed in with this same tool, square and flat for a no-leak fit. This tool will also pull cam cover from case. 978236 70-99 B.T. (excl. TC) 978236 MCS, CAM SEAL REMOVER/INSTALLER KIT Used to install and remove the camshaft seal, without removing the cam cover. Can also be used to pull a stubborn cam cover from the crankcase. 925566 70-99 B.T. (excl. Twin Cam) 925566 JIMS, BREATHER REAMER TOOL Used to repair the (often damaged by OEM plastic breather valves) breather hole. No need to disassemble the cases. This tool will ream the hole to +.030" so a replacement steel +.030" JIMS or S&S breather can be installed. Note: After the reaming process all aluminum reaming chips must be removed. Also, when working on early 36-69 cases, before reaming check if wall thickness in the breather hole is thick enough so the reamer will not break through. 978343 36-99 B.T. (excl. TC) 978429 Replacement reamer only 978343 979419 979418 GEORGE'S GARAGE, TC CAM RELIEF TOOL Used to machine the engine case for high lift cams. Fits 99-06 Twin Cam (excl. 2006 Dyna). Will fit 2006 Dyna and all 07-17 Twin Cam models when used with 979420 relief pilot tool. Relief tools for 99-06 Twin Cam (excl. 2006 Dyna) 979418 Single spindle 979419 Dual spindle Relief pilot for 06-17 Dyna; 07-17 Softail; 07-16 Touring Used with 979418 and / or 979418 (99-06) relief tools, for use with Twin Cam models with (06-17) hydr. chain tensioners. 979420 Relief pilot JIMS, 70-99 CAM RELIEF TOOL Used to remove material from crankcase to install larger than stock cam. Can be driven by a standard motor drill with a 1/2" chuck. 978473 70-99 B.T. (excl. Twin Cam) 978473 979420 JIMS, XL/BUELL CAM RELIEF TOOL Used to remove material from crankcase to install larger than stock cams. Can be driven by a standard motor drill with a 1/2" chuck. 978474 91-22 XL; 95-10 Buell (excl. 1125 models) 978474
RkJQdWJsaXNoZXIy ODQ0NDEw