303 V-TWIN TOOLS NEW PRODUCTS ADDED WEEKLY AT MOTORCYCLESTOREHOUSE.COM LOWER END FEULING, M8 OIL PUMP TESTER Used to bench test Feuling M8 oil pumps (tester will not fit OEM M8 pumps). Used for PSI pressure opens the relief valve. The spring tension can be adjusted to achieve the desired pop-off PSI. Tool includes: air regulator, 0 - 100 psi pressure gauge, plugs for water and oil cooled oil pumps, gasket & needed hardware. Feuling® recommends the oil pump relief valve be seated and sealed from 0-30 psi with full pop-off at 50-60 psi. Note: Will not fit OEM pumps. 17-22 M8 with Feuling oil pump 588061 Oil pump tester 588061 FEULING, OIL PUMP PRESSURE RELIEF VALVE TEST TOOL Used to bench test the camshaft support plate to ensure the working of oil pump pressure relief spring, a correct sealing relief valve and correct pop-off pressure to solve any issues in the engine before it hits the road. Works with all Twin Cam support plates. Includes air regulator, 0-100 psi pressure gauge, gasket & required hardware. Note 1: Perfect to test the Feuling 566114 oil pressure relief spring, enabling you to set pop-off pressure to your preference. Note 2: Feuling recommends 0-30 psi with full pop-off at 55-60 psi. 99-17 Twin Cam 566117 Relief valve test tool Replacement parts For 566117 tool. 588063 Air regulator 566118 Gasket 566117 566118 MCS, TAPPET GUIDE PULLER TOOL Used to pull the press fitted tappet block body from the XL Sportster crankcase. Repl. 95724-57. 925578 57-E78 XL 925578 JIMS, TAPPET BLOCK PULLER TOOL Used to remove the press fitted tappet guides from the right side crankcase. Repl. 95724-57 978308 57-78 XL 978308 JIMS, SOLID BRASS PUNCH SET - OIL PUMP 4-piece punch set used to seat the check ball, without damage to the ball, in the oil pump for a perfect seal. Includes 3/8" x 6", 1/2" x 8", 5/8" x 9" & 3/4" x 10" punches. 978311 978311 JIMS, TAPPET BLOCK CLEARANCE CUTTER TOOL Used to give tappet blocks adequate clearance when high lift cams are used. Professional results in minutes. 961426 84-99 Evo B.T.; 86-90 XL 961426 JIMS TAPPET BORE REAMER TOOL Used to ream worn or damaged tappet bores to +.010" oversize. Kit includes reamer and two flex hones for a perfect bore finish. Note: Oversized tappet 961569 is required and must be ordered separately. 99-17 Twin Cam; 17-22 M8; 00-22 XL; 08-12 XR1200; 00-10 Buell XB 961550 +.010" o.s. reamer tool 961569 +.010" o.s. tappet 961569 961550 LANG TOOLS, OIL PRESSURE SENDING UNIT WRENCH Used to install and remove 26561-99 / MCS 904721 oil pressure switch. Special low profile 15/16" sized reversible wrench with vinyl grips. Dimensions: 10.625" x 4" x 1.5". 514549 99-16 FLHR/C models 514549 OIL PRESSURE SWITCH WRENCH Used to remove and install oil pressure sending units without damage to switch unit. The extension piece of the handle is not used on XL models. Repl. 34816. 500557 84-99 Evo B.T. (excl. FLT, FLHT) and L83-85 XL 500557
RkJQdWJsaXNoZXIy ODQ0NDEw