304 V-TWIN TOOLS LOWER END 566122 FEULING, HYDRAULIC LIFTER OIL SQUIRT CAN Used to fill hydraulic tappets prior to assembly to avoid dry running on initial start-up. 566122 53-22 Big Twin; 86-22 XL 962005 JIMS, TAPPET PUMP TEST STAND Used to check for loose or spongy feeling tappets, with pressurized oil, prior to installing. Easy to diagnose inadequate sealing tappets before they present an issue in the running engine. Requires oil, compressed air and a drill press for testing. Note: To test Evolution tappets the Evolution insert 962006 must be purchased separately. Complete kit (excl. Evo insert) 962005 9 9-17 Twin Cam; 17-22 M8; 00-22 XL; 08-12 XR1200 and 00-10 Buell XB Insert only for Evo 962006 84-99 Evo B.T.; 86-90 XL 962006 TAPPET ROLLER TOOL Used to remove and install tappet rollers on all 36-99 B.T. and 57-99 XL models (excl. 1999 Twin Cam and Flatheads). Mounts in a regular workbench vise to apply pressure. USA made. 516925 36-99 B.T.; 57-99 XL (excl. Flatheads, Twin Cam) 516925 978643 JIMS, TAPPET HOLDING TOOL Used to store the tappets and anti-rotation pins when removed from the engine. Enables re-installation in the same position. Tappet locations are clearly mentioned on the holding tool. 978643 99-17 Twin Cam; 17-22 M8; 00-22 XL; 08-12 XR1200; 00-10 Buell XB JIMS, TAPPET BLEED TOOL A special jar to hold four hydraulic tappets. Once vacuum has been applied the lifters will fully bleed-down and prevent possible damage to the valve train after initial engine start due to incomplete bleeded tappets. 962043 84-22 B.T.; 86-22 XL; 08-12 XR1200; 00-10 Buell XB 962043 FEULING, PUSHROD TUBE HOLDER TOOL Used to hold pushrod tube up when adjusting pushrods. 566121 Pushrod tube holder 566121 GEORGE'S GARAGE, PUSHROD CLIP INSTALLER TOOL Used to push down the 17945-36B pushrod spring cup and easily install the pushrod retainers without damage to the pushrod clip/spring cover. 979427 36-22 B.T.; 57-90 XL 979427 MCS, PUSHROD TUBE HOLDER TOOL Used to prevent the lower pushrod from falling down when doing pushrod adjustments. Compatible with 9122 XL Sportster models that are custom equipped with multiple parts pushrods. 925537 36-22 B.T.; 57-90 XL 925537 JIMS, MAGNETIC TAPPET HOLDING TOOL This tool will hold the tappets inside the tappet bores of the engine, in the same position, when the cam is removed. Simply install the tool over the tappet cover and the rare earth magnets will magnetically hold the tappets in place. Includes a form fitted tray that will protect the magnets from damage when stored. 99-17 Twin Cam; 17-22 M8 engines 939481 939481 MOTION PRO, PUSHROD COVER PLIER TOOL Used to push down the spring cup to easily remove and install the pushrod retainers on multiple-parts H-D pushrod covers. No more scratched engine parts from using a screwdriver between the cooling fins. Flat portion of tool fits under the cylinder head while cupped end fits over the bell in the tube and then compresses the spring allowing for easy access to the spring cap retainer. 36-17 B.T. (excl. M8); 57-90 XL 948377 948377 FEULING, LIFTER BLOCK BORE MEASURING KIT Used to check the correct bore diameter and roundness of the lifter bore diameter. Includes 5 precision ground round steel balls. Feuling advises a tolerance of 0.001" to 0.0015". Sizes include: 0.8430", 0.8435", 0.8440", 0.8445" and 0.8450". 588060 84-22 B.T.; 86-22 XL; 08-12 XR1200; 00-10 Buell XB 588060
RkJQdWJsaXNoZXIy ODQ0NDEw