305 V-TWIN TOOLS NEW PRODUCTS ADDED WEEKLY AT MOTORCYCLESTOREHOUSE.COM LOWER END JIMS, PUSHROD CLIP TOOL Used to push down the 17945-36B style spring cup/ cover, so the pushrod retainers can be installed/removed without damage on all H-D® pushrod covers. This tool will let you do it with one hand, without damage to the spring cover, like can happen with a screwdriver. Manufactured from non-scratching black delrin. 961575 36-22 B.T.; 57-90 XL 961575 JIMS, PUSHROD COVER SEAL/SEAT CUTTER Used to cut head & tappet blocks in-line with each other for a positive pushrod to o-ring seal. Perfect to correct misalignment issues for when pushrods refuse to seal. 961413 84-99 Evo B.T.; 86-90 XL 961413 978612 S&S, FLYWHEEL BALANCE KIT FOR 5-PIECE CRANKS Kit is for for use with 5-piece cranks only. 512538 Balance kit for 5-piece cranks 512538 JIMS, CRANKCASE SPLITTING TOOL Used to split the engine cases and easily break the sealer. This crankcase splitter is the only correct tool that will allow you to easily split the cases, without risk of damage, with a ratchet. Manufactured from 1/2" thick A36 hot rolled steel. Note: Do not use air or electric impact tools. Instructions included. 55-06 B.T. (excl. 2006 Dyna) Will split cases and also press the complete flywheel out of and into the right case on Timken bearing models. Some case pressing may require a hard cap. See 514024 for hard cap to protect sprocket shaft. Note: For the 00-06 Softail engine this tool can be used for removing the flywheel from the left case only. 514023 Crank removal tool 514024 Hard cap. Protects sprocket shaft when using crank assembly removal tool 514023 17-22 M8 models Works on both Softail and Touring models. Installs to the primary side of the case. 920252 Crankcase splitter 514023 JIMS, FLYWHEEL HOLDER TOOL Is to be clamped in a workbench vise. Holds the sprocket shaft, with or without flywheels and with or without the left case attached. 978284 55-06 B.T. (excl. 2006 Dyna) 961431 06-17 Dyna; 07-17 Softail; 07-16 Touring 978284 JIMS, CONNECTING ROD LAP SET Used on all models with replacable connecting rod races. Includes 1-1/2" and 1-5/8" OD laps. 978407 Lap set. 36-99 B.T. (excl. Twin Cam) and 57-99 XL Replacement parts Replacement parts for 978407 lap set. 978409 Lap head 1-1/2" OD 978410 Lap head 1-5/8" OD 978410 978409 978407 JIMS, CONNECTING ROD RACE TOOL Used to support both sides of connecting rods when races are removed or installed, minimizing the possibility of distorting the female rod or race. 978320 36-99 B.T. (excl. TCA); 52-99 XL and all Flathead models 978320 JIMS, TAPPET ADJUSTMENT TOOL Used to check correct free play on the hydraulic tappet. Insert the tip under the hydraulic unit retaining clip, above pushrod seat. If it does not fit or if up & down play is evident, the tappet is out of adjustment. Note: Does not work on solids, JIMS Hydrosolids or others with limited travel. 978612 84-22 Big Twin; 86-22 XL; 08-12 XR1200; 00-10 Buell XB MCS, FLYWHEEL HOLDING TOOL Used to insert the sprocket shaft. The tool is clamped in a vice. This way the flywheel assembly is held, with or without the left case installed. 06-17 Dyna; 07-17 Softail; 07-16 Touring 925564 925564
RkJQdWJsaXNoZXIy ODQ0NDEw