308 V-TWIN TOOLS JIMS, TWIN CAM CRANKCASE ROLLER TO TIMKEN BEARING CONVERSION TOOL Used to replace the cheap low quality sprocket shaft roller bearing (OEM 24604-00C/D and 24605-07 which is used by the The Factory to save money in 03-17 Twin Cam models). With this conversion tool the much stronger and durable early Timken bearing (OEM 9028 / MCS 508960), that was used up to 2002, can be installed. This tool includes a new steel bearing insert and a press plate that will hold the bearing insert in line with the case bearing bore when it is pressed into the case. Also included all drill bits to drill oil feed and return holes, hardware and detailed instructions. Advised in any high performance application. Note 1: Order required Timken bearings (MCS 508960 / OEM 9028) separately. One MCS 978519 insert kit is included with 978517 conversion tool kit. Note 2: Use JIMS tool MCS 978340 for race installation 978517 Conversion tool kit 03-17 Twin Cam Replacement parts 978519 Crankcase insert kit only 03-17 Twin Cam 978517 978332 978505 978331 978335 JIMS, SPROCKET SHAFT BEARING INSTALLER TOOL Used to install the crankshaft assembly into the left crankcase Timken bearing. *Note 1: Socket MCS 978332, which is needed with this tool, must be ordered separately. See description and photo of these tools, also on this page. *Note 2: Use MCS 978334 and MCS 978335 for 77-03 XL, Buell models. These must be ordered separately. See description at 'JIMS, install tools sprocket shaft' below. Note 2: For 06-17 Dyna; 07-17 Softail; 07-16 Touring models, add MCS 978505 adapter kit. 978331 55-02 B.T., Twin Cam (*Note 1) 978333 52-03 XL; 94-02 Buell (*Note 1 and *Note 2) 06-17 Twin Cam adapter kit Bearing & race installer adapter kits for 6-speed models with fine spline sprocket shafts. Used with MCS 978331 tool. 978505 06-17 Dyna; 07-17 Softail; 07-16 Touring 77-03 XL; 94-02 Buell These are tools that are additionally required when using JIMS sprocket shaft bearing installer tool MCS 978333 for 77-03 XL Sportster and 94-02 Buell models. Use tool MCS 978334 to install the bearing until tool runs out of threads, then install tool MCS 978335 to push the bearing the rest of the way. 978334 Install tool 2.060" long, use with MCS 978333 978335 Install tool 2.500" long, use with MCS 978333 JIMS transmission sprocket / pulley nut wrench Transmission sprocket tool which is also used with JIMS sprocket shaft bearing installer tool MCS 978331 (Big Twin models) and MCS 978333 (XL, Buell models). This extra long 2-piece design gives the best control on the torque of the sprocket shaft bearing pack for checking bearing end play. 978332 Socket for use with MCS 978331 & 978333 LOWER END 530726 LISLE, REMOTE STARTER BUTTON FOR WORKSHOP USE Used in the workshop to rotate the engine by momentarily activating the starter. Great for tappet adjusting & other adjustments or servicing. Simply hook up to starter motor positive and negative post. With 4 ft. length insulated cable. Note: Keep ignition switch turned off to prevent engine starting. 530726 Remote starter button 978340 JIMS, SPROCKET SHAFT BEARING RACE INSTALLER Used to install bearings in the left crankcase. This tool will help to press in the bearing race absolutely straight. A must for the later engine cases. Note: For removal of races see MCS 978337. 978340 69-02 B.T.; 77-03 XL; 87-02 Buell JIMS, SPROCKET SHAFT BEARING & RACE PULLER TOOL Multiple application puller. * Used to remove Timken® bearing OEM 9028 or OEM 9029 on 55-02 Big Twins. * Used to remove sprocket shaft inner bearing race on 03-17 Twin Cam models. * Used to removes pinion shaft inner bearing race on 54-22 XL Sportster and 87-10 Buell (excl. 1125). * Used to correctly remove press fit transmission gears and bearings from input and output shafts on all 0217 V-Rod. 978509 55-02 B.T.; 03-17 Twin Cam; 57-22 XL; 87-10 Buell (excl. 1125) and 02-17 V-rod 978509 JIMS, SPROCKET SHAFT BEARING PULLER TOOL Used to easily remove the inner Timken bearing from the sprocket shaft without removing shafts from the flywheels. Big Twin 978329 55-85 B.T. (OEM flywheels) and 55-99 B.T. with aftermarket flywheels (excl. Twin Cam) 978330 86-02 B.T., Twin Cam (OEM flywheels) XL Sportster 978327 57-76 XL 978328 77-03 XL; 87-02 Buell 978329 979473 GEORGE'S GARAGE, SPROCKET SHAFT BEARING RACE TOOL Used to remove and install the Timken sprocket shaft bearing race in the left side engine case. To be used with 979461 driver handle and 979462 wedge spacer. 979473 96-02 Big Twin
RkJQdWJsaXNoZXIy ODQ0NDEw