309 V-TWIN TOOLS NEW PRODUCTS ADDED WEEKLY AT MOTORCYCLESTOREHOUSE.COM LOWER END JIMS, SPROCKET SHAFT BEARING RACE TOOL Used to install and remove sprocket shaft bearing race from left side crankcase. Note: Used with 920542 JIMS driver handle which must be ordered separately. 978337 69-02 B.T. 978338 77-03 XL; 87-02 Buell 978337 978339 JIMS, TOOL DRIVER SPACER Can be used with all JIMS 2-piece bearing race tools. The effectiveness of any bearing race remover tool is closely linked to the tools ability to grip the race. This special spacer applies outward force to the race remover tool so the grip to the race will be maximized, for best race removal. 978339 X-tra grip tool driver JIMS, SPROCKET SHAFT SNAP RING INSTALLER & REMOVER Used to install and remove the retaining ring (snap ring) of the Timken bearing outer race in the right side crankcase. A must for replacing retaining rings in cases without inserts. Will prevent damage to the aluminum of 90-02 crankcases during installation. 978341 69-02 B.T. 978341 920542 JIMS, RACE & BEARING DRIVER HANDLE Used with many JIMS tools. Amongst others MCS 978289, 978290, 978337, 978338, 978238, 978356, 978376 and 978417. Approx. length 12 inch (30.5cm). 920542 Driver handle JIMS, SPROCKET SHAFT BEARING NUT WRENCH Used to install and remove sprocket shaft bearing nut. 978322 55-68 B.T. 978322 LANG TOOLS, SPROCKET SHAFT BEARING END-PLAY TOOL Used to set-up correct end-play of the tapered sprocket shaft bearings in the left side crankcase. Tool is little smaller in diameter than actual sprocket shaft. This allows bearing races to be installed and removed without pressing them on and off the tool. End-play can be measured with a dial indicator. USA made. 514168 69-02 B.T. 514168 978321 JIMS, SPROCKET SHAFT SEAL INSTALLER Used to install sprocket shaft seal / crankshaft main seal in left side case, straight and without distortion. 70-17 B.T. (excl. M8) Installs OEM 12026B and 12068 sprocket shaft seal. 978321 70-17 B.T. (excl. M8) 95-22 XL; 08-12 XR1200; 95-10 Buell Installs 12068 sprocket shaft seal. Note: 978324 must be used with 576558 driver handle which is sold separately. 978324 95-22 XL; 08-12 XR1200; 95-10 Buell XB 576558 Driver handle for 978324 18-22 Softail; 17-22 Touring, Trikes Installs OEM 11000134 (MCS 568378) sprocket shaft seal. Alternator stator can stay in place during seal installation. 559403 18-22 Softail; 17-22 Touring, Trikes 978324 JIMS, TIMKEN ® BEARING SIMULATOR Used to allow easy removal and replacement of the flywheel assembly in the left crankcase when checking rod to case, piston to flywheel and cylinder to flywheel clearances. Made from black delrin plastic so bearing races will never be scratched or otherwise damaged from the simulator. 978342 70-02 B.T. 978342 979425 GEORGE'S GARAGE, SPROCKET SHAFT SEAL INSTALLER TOOL Used to press sprocket shaft seal into left crankcase, with sprocket shaft installed. 979425 69-17 B.T. (excl. TC) 978326 JIMS, COMPENSATING SPROCKET SHAFT NUT WRENCH Used to install and remove the primary drive compensating sprocket nut. 978326 55-70 B.T.; 57-70 XL JIMS, SPROCKET SHAFT SEAL PULLER Used to remove OEM 11000134 / 568378 sprocket shaft seal / crankshaft main seal from left engine case without damage. Pulls seal square to the bore by turning a wrench. 18-22 Softail; 17-22 Touring, Trikes 569209 569209
RkJQdWJsaXNoZXIy ODQ0NDEw