310 V-TWIN TOOLS LOWER END JIMS, CRANKSHAFT GUIDE TOOL This tool will spread crankcase pinion bearing rollers while re-assembling right side engine case onto flywheel assembly. 978224 99-17 Twin Cam; 17-22 M8; 03-10 Buell XB 978224 978411 JIMS, CRANKCASE LAP TOOL Pinion bearing race lap tool. Removes more material in less time but with greater accuracy than a conventional lap. The JIMS case lap is guided on both sides of the pinion bearing race. This additional support on the cam gear side of the bearing race is achieved by means of a bolt on the base plate that precisely locates a drill bushing in which the lap turns. This base plate is located on the same engine case pins as the cam cover. The positioning of this drill bushing is held within .0002" to the engine case pins and within .0002" of the case centerline. Now, instead of guiding only from the left side with Timken bearings, which are a floating fit, the JIMS case lap uses a special ground bearing sleeve to hold the left side of the lapping shaft without movement. Both ends of the lap are supported precisely in the same centerline as the flywheel assembly. With this extreme rigid arrangement it is possible to power the lap with a low speed drill motor without fear of chatter in the lapped bearing race. The JIMS lap can still be powered by the conventional hand crank when desired. It is recommended to use JIMS 978341 (snap ring installer & remover tool), especially on 9099 crankcases. 978411 58-99 B.T. cases (excl. TC) Replacement lap head 978412 1-3/4" OD case lap MCS, PINION BEARING RACE TOOL Used to remove the pinion bearing race / pinion shaft bushing (24599-58A/B, 24599-93) from the right side crankcase. Repl. OEM 39958 tool. 58-99 B.T. (excl. Twin Cam) 925562 925562 GEORGE'S GARAGE, CRANKSHAFT BEARING TOOL Used to remove & install left sprocket shaft & right side pinion shaft crankcase bearing. Aligns bearing straight, will not damage engine case. 979470 99-02 TCA (excl. TCB Softail). (Pinion) 979471 03-17 TCA (pinion & sprocket); 03-17 TCB (sprocket) 979471 JIMS, ALTERNATOR ROTOR PULLER Pulls the rotor from the sprocket shaft. Especially helpful with the strong magnetic hold on 45 Amp charging systems. Will not damage sprocket shaft threads. Will pull 29981-95 (38 Amp) and 29999-97A/B (45 Amp) style rotors. 978393 Various 95-06 Touring models 978393 EVOLUTION INDUSTRIES, ALTERNATOR ROTOR PULLER Used for easy removal of the alternator rotor from the strong magnetic hold of 45 Amp charging systems. Will fit most rotors with a two hole system. Simply insert, pinch and pull tool to remove rotor. 552105 Rotor puller 552105 JIMS, 99-17 CRANKSHAFT BEARING TOOL This quality tool is designed to remove and install crankshaft bearings the JIMS way, quick and professional. 99-02 Twin Cam (excl. Softail) Removes & installs the right (sprocket shaft) side crankshaft bearing on Twin Cam A engines (Dyna & Touring). Precision made and piloted using delrin, a non-marring material, to help press bearings in and out straight, with no damage to the case. 978222 99-02 Twin Cam (excl. Softail) 03-17 Twin Cam Removes & Installs left & right side crankshaft bearing on Twin Cam A engines (Dyna & Touring). Removes & installs left (sprocket shaft) side crankcase bearing on Twin Cam B engines (Softails). Precision made and piloted using delrin, a non-marring material, to help press bearings in and out straight, with no damage to the case. 978246 03-16 TCA (left & right side); 03-17 TCB (left side) 00-17 Softail (excl. Dyna, FLT/Touring) Used to remove & install the right (pinion shaft / cam) side crankshaft bearing on Softails. Protects the crankcase from damage by using a special designed support block for both removal and installation of the bearing. 978388 Right side 978222 JIMS, PINIONSHAFT BUSHING TOOL This tool will remove and install 25344-99 / MCS 921146 pinionshaft bushing in the cam support plate of all 99-10 Twin Cams. This tool is piloted for accurate operation. After 2010 these bushings are no longer used. 978223 99-10 Twin Cam 978223 JIMS, M8 ALTERNATOR ROTOR TOOL Pulls and installs alternator rotor as used on M8 motors. Overcomes the strong pull of the high performance rare earth magnets that are used with ease. Prevents damage by using inappropriate tools as hammers or pry bars. 559406 18-22 Softail; 17-22 Touring 559406 JIMS, BALANCER SHAFT REMOVAL TOOL Used to remove both front & rear counter balancer shaft bearing assembly. 978508 07-17 Softail 978508
RkJQdWJsaXNoZXIy ODQ0NDEw