311 V-TWIN TOOLS NEW PRODUCTS ADDED WEEKLY AT MOTORCYCLESTOREHOUSE.COM LOWER END 925554 MCS, 45A ALTERNATOR ROTOR PULLER TOOL Used to pull the alternator rotor from the sprocket shaft, without issues associated with strong magnets. Pulls simple and direct without damage to any components. Designed for use on most Touring models with 45 Amp high output rotors that have 2-hole style threaded 'pull holes'. 925554 H-D Touring with 45A style rotors JIMS, BALANCER SHAFT ALIGNMENT TOOL A must for maintaining a long life of balancer drive chains and bearings. Takes the guess-work out of setting up the sprocket & chain assembly on Twin Cam Softail models. This tool must be treated with great care, as you would treat a micrometer. 978416 00-17 Softail 978416 JIMS, BALANCER SHAFT & BEARING INSTALLER TOOL Used to align and safely install a new balancer bearing and counter balancer shaft into the Softail engine case. 978500 07-17 Softail 978500 JIMS, BALANCER BEARING TOOL Used to remove & install OEM 35200021 balancer bearings on M8 models. 18-22 Softail; 17-22 Touring, Trikes Remover tool Used to pull the balancer bearings, straight and without damage from the crankcase. 574507 Remover tool Installer tool Used to install balancer bearings in the correct location to prevent engine problems at a later moment due to incorrect installation. Aligns bearings to the crankcase via case bolt and dowel locations, allowing the mechanic to install the bearings on a workbench without the use of a driver or press. 577073 Installer tool 577073 574507 MCS, BALANCER SHAFT ALIGNMENT TOOL Used to set-up correct alignment of the sprockets / balancer chain to insure maximum life and dependability from the balancer chain and bearings. 925553 00-17 Softail 925553 JIMS, BALANCER SHAFT RETENTION PINS Used to secure the engine balancers when servicing the flywheel assembly. This tool locks into the balancer's sprocket pin holes and prevents the balancer turning out of synchronization with the flywheel. 978418 00-17 Softail 978418 JIMS, BALANCER INTERCONNECT SEAL LEAK TEST TOOL Used to check the condition of the new or old interconnect seal H-D 45359-00 / MCS 981195. If seal leaks an over oil condition in the lower end can be created, resulting in increased oil carry over. Testing seal is advised each time the cam support is re-installed. Note: A leak-down tester, like JIMS 961581, is required. 962001 00-17 Softail 962001 JIMS, HYDRAULIC BALANCER RETAINER TOOL Used to hold the hydraulic tensioners in place while servicing the Softail engine balancing system. 962000 00-17 Softail 962000 JIMS, INNER BALANCER BEARING TOOL Used to accurately, and safely install or remove the inner balancer bearing mounted in the left engine case. Tool is designed for both early and late Softail Twin Cam crankcases. Work can be done on a workbench without using a press. 961555 00-17 Softail 961555 JIMS, OUTER BALANCER BEARING TOOL Used to Install & remove the outboard balancer bearing that is installed in chain guide support plate. 961430 07-17 Softail Replacement parts 978504 Outer bearing remover / installer only 961430 JIMS, TCB CASE SUPPORT BLOCK TOOL Used to support the outer side of the Softail crankcase, underneath the balancer bearing pads surface. Aluminum with an inserted Delrin pad to help prevent marring. Perfect for when working on the crankcase balancer bearings or other general engine work. 961556 00-17 Softail 961556 925555 MCS, INNER BALANCER BEARING TOOL Used to install or pull the inner engine balancer bearing (8992A / MCS 507698) from the left case. Work can be done on a workbench and does not require a press. 925555 00-17 Softail
RkJQdWJsaXNoZXIy ODQ0NDEw