318 V-TWIN TOOLS 978646 JIMS, 6-SPEED TRANSM. SHAFT VISE STAND Stand is securely to be clamped in a vice. Used to hold the transmission shafts in perfect alignment for a quick and efficient assembly. 978646 06-17 Dyna; 07-22 Softail; 07-22 Touring 4/5/6 SPEED SHIFTER SHAFT SEAL INSTALLER Used to install shifter shaft seal effortlessly centered, aligned and to correct depth. Used to install 12045 seal on 80-06 B.T. and 37101-84B seal on 06-13 6-speed 'Cruise Drive' models and 84-05 4&5-speed XL Sportsters. JIMS MCS 962016 951572 80-06 5-sp B.T. (excl. 2006 Dyna) 962015 951573 06-13 Dyna; 07-13 Softail, Touring; 84-05 XL 962016 962015 JIMS, SHIFTER FORK SHAFT REMOVER TOOL Used to loosen and remove both shifter fork shafts 35223-06A and 35222-06A, from the transmission door to allow further disassembly of the 6-sp. transmission. 978498 07-22 Softail; 07-22 Touring; 06-17 Dyna 978498 TRANSMISSION JIMS, SHIFT FORK ALIGNMENT TOOLS Used to set and align the shifter forks on 4-speed Big Twin transmissions. 513765 37-E79 4-sp B.T. Repl. 96384-39 513766 L79-86 4-sp B.T. 513765 JIMS, 4 & 5-SP TRANSM. STAND SOFTAIL Can be used to clamp the transmission case in a workbench mounted vice. When used for 5-speed transmissions washers must be used to space the stand. Note: Not compatible with models with rubber mounted engines/transmissions. 978272 36-86 4-sp B.T.; 84-99 Softail 978272 JIMS, 5-SP TRANSM. STAND (RUBBER) Will fit 5-speed rubber mounted, without transmission oil pan, models only. 978271 80-93 FLT, FXR, Dyna models 978271 979439 979438 GEORGE'S GARAGE, TRANSM. PULLEY / SPROCKET NUT SOCKET Used to install & remove the sprocket/pulley locknut on the transmission mainshaft. Works with both belt & chain drive models. With inner pilot for good alignment and 1/2"drive. 979438 36-06 B.T. (excl. 2006 Dyna) (1-7/8" hex) 979439 07-22 Softail, Touring; 06-17 Dyna (2-1/4" hex) 978332 978488 962048 MCS, TRANSMISSION PULLEY NUT SOCKET Used to install and remove the large hex nut that holds the transmission pulley. 36-06 B.T. (excl. 2006 Dyna) Removes and installs the 1-1/2"-24 hex nut. (35211-36 and 35211-91A). 925540 4 and 5-speed models 06-17 Dyna; 07-22 Softail; 07-22 Touring Removes and installs the 2-1/4" hex nut (35241-06). 925544 6-speed models JIMS, TRANSMISSION PULLEY NUT SOCKET Used to install or remove the thin but large left hand threaded nut that holds the rear transmission sprocket/ pulley on the mainshaft. Heavy-Duty extra thick wall design. Socket comes with a 1/2" drive. 36-06 B.T. (excl. 2006 Dyna) Removes and installs the 1-1/2"-24 hex nut. (35211-36 and 35211-91A). 978332 4 and 5-speed models 06-17 Dyna; 07-22 Softail; 07-22 Touring Removes and installs the 2-1/4" hex nut (35241-06). 978488 6-speed models 91-22 XL; 87-10 Buell (excl. 1125R) Removes and installs the 2-1/2" hex nut (35211-91B). Although the much longer Big Twin socket (MCS 978332) will fit the nut, the mainshaft on XL Sportster models does not extend through for the guidance collar to ensure correct alignment. This shorter socket is easier and safer to handle, providing full contact with the nut. 962048 5-speed models EVOLUTION INDUSTRIES, TRANSM. PULLEY / SPROCKET NUT WRENCH Used to remove & install the large nut that holds the transmission pulley or transmission sprocket on the transmission mainshaft. Works with both belt & chain drive models. 1/2" drive. One-piece, no-welds narrow body to prevent mass and give maximum effectivity of air impact wrenches. 552103 36-06 B.T. (excl. 2006 Dyna) 552104 07-22 Softail; 07-22 Touring; 06-17 Dyna 552103 552104 519751 TRANSMISSION PULLEY/SPROCKET NUT WRENCH Fits transmission sprocket nut on 36-E84 4-speed Big Twin with one-piece transm. mainshaft bearing. Note: Will fit L84-06 5-speed B.T. transmissions only when inner bearing ring 34090-84/34091-85A is first removed since inner diameter of tool is not large enough to clear this crimped-on bearing ring. Repl. 94660-37A. 519751 36-E84 4-sp B.T 925544 925540
RkJQdWJsaXNoZXIy ODQ0NDEw