325 V-TWIN TOOLS NEW PRODUCTS ADDED WEEKLY AT MOTORCYCLESTOREHOUSE.COM FRONT END MCS, FORK SEAL & CAP INSTALLER TOOL KIT Used to install fork seals and fork caps without damage to the seal lip. This tool can be used for 35mm, 39mm and 41mm fork tubes. Includes a special 39mm POM cap 925557 925557 925514 MOTION PRO, 39MM & 41MM FORK SPRING COMPRESSORS Used to help install fork tube plugs on forks with a lot of spring pre-load. Will work on most 39mm and 41mm H-D® front ends. 547232 39 & 41mm kit 547233 41mm kit 547234 39mm kit Replacement parts 547237 41mm socket 547231 39mm socket 547232 MOTION PRO, SPRINGER FORK SPRING TOOL Used to help assemble and disassemble Softail Springer type front forks. 547240 88-11 Softail FXSTS, FLSTS Springers 547240 JIMS, VACUUM FORK FILLER Used to change the fork oil in full dressers. Around 2 hours would be expected when doing a fork oil change, this tool makes it around 30 minutes. Will work on all other models as well, except those with upside down or cartridge type forks. Note 1: The 978614 hand vacuum tool is required for use with the 978613 Vacuum fed fork filling tool. Note 2: Will not work on upside down or cartridge type forks. 978613 Vacuum fed fork filling tool 978614 Mityvac hand vacuum pump kit 978613 978614 Dresser fork servicing time up to 75% quicker! LANG TOOLS, FORK SLIDER OIL FILLER Plastic tube with a M8 x 1.25 threaded nipple allowing you to simply fill the fork slider with oil through the oil drain / damper tube mount hole with a vacuum pump. The M8 x 1.25 threaded nipple will fit many H-D models. 514348 Fits most H-D with air supported forks 514348 PS, GAUGE MOUNTED PUMP Compact air pumps for air pressure adjustments to front fork or shock absorbers. The 30 PSI and 60 PSI version is mainly used on forks and the 100/300 PSI mainly for shocks. Note: For Airtail shocks maximum pressure is around 160 psi (11 bar). Analog 974176 With 30 PSI (2.1 bar) gauge 974177 With 60 PSI (4.1 bar) gauge 974178 With 100 PSI (6.9 bar) gauge 974179 With 300 PSI (20.7 bar) gauge Digital +- 0.5 psi (0.034 bar) precision. Flexible hose with no-loss connector. Will reach air valves in tight spaces. 974739 With 0-300 PSI (0-20.7 bar) gauge 974176 974739 MCS, STOPPER PLATE & PULL-UP TOOL Used to install the cartridge kit in cartridge type front forks. Fits most Ohlins NIX22 and FKC101. Repl. 01765-08 Ohlins pull up tool and 02810-03 Ohlins stopper plate. all H-D models with Ohlins FKC101 kit 99-06 FLHTCI; 99-06 FLHTC; 07-13 FLHTC; 99-06 FLHT; 07-13 FLHT; 97-99 FLHT; 11-13 FLTRX; 99-06 FLTR; 07-13 FLTR; 11-13 FLTRU; 99-06 FLHRC; 07-13 FLHRC; 97-99 FLHRC; 99-06 FLHRCI; 04-08 FLHRS; 99-06 FLHR; 07-13 FLHR; 97-99 FLHR; 2006 FLHX; 07-13 FLHX; 99-06 FLHTCUI 925569 925569 JIMS, CARTRIDGE FORK COMPRESSOR TOOL Used to compress the front springs in cartridge style forks when servicing or rebuilding. The compressor can be mounted in a vice for easy handsfree servicing. Includes adapter for 02-05 FLT forks to eliminate direct contact with spring coil and a special rod to pull-up the fork damper rod. For Std length forks 978477 All H-D with cartridge style forks 978477 MCS, 39MM & 41MM FORK SPRING COMPRESSOR KIT Used to help install fork tube plugs on forks with a lot of spring pre-load. Will work on most 39mm and 41mm H-D® front ends. 925514 39 & 41mm kit MCS, SPRINGER ROCKER STUD TOOL Used to install and remove the rocker studs on Springer forks. Comes with a pilot to simplify removal and installation. Helps prevent damage to the slot of the studs. 30-52 45" (750cc) Flathead 925574 925574
RkJQdWJsaXNoZXIy ODQ0NDEw