www.zodiac.nl 26-023 750338 Pin extractor 750339 Receptacle extractor No more difficulties in dismounting molex style connectors. The receptacle and pin extractor will easily remove the pins. Can be used on all models. 5790 JIMS RECEPTACLE AND PIN EXTRACTOR 751056 Works on all Touring models 2003 thru 2013 and all V‑Rod models 2002 to present. 753616 Works on all Touring models 2014 to present These Jims‑USA tools will help to align the ignition switch housing and ignition switch knob to help extend the life of the ignition switch housing. Just insert the tool, torque de screws and remove the tool again. 5788 JIMS IGNITION SWITCH HOUSING ALIGNMENT TOOLS 751123 Works on 2010 to present Touring front and rear pipe. Must be used with a 3/8" drive torque wrench 751104 Works on 2012 thru 2017 Dyna and V‑Rod front and rear pipe, and 2012 thru 2017 Softail front pipe 751105 Works on 2012‑2017 Softail rear pipe USA made wrenches to install and remove the M14, 4‑wire heated O2 (Oxygen) sensors without taking off the exhaust pipes from the bike. 5786 JIMS O2 SENSOR WRENCHES 751055 Fits all unheated Fuel Injected Oxygen Sensor equipped models 2006‑present This tool is used to remove or install the oxygen sensor on all FLH and FLT series Touring models 2006 thru 2009, Softail, Dyna and V‑Rod 2006 thru 2011, 2007 to present Sportster and closed loop fuel injected Buell models. Socket has a 3/8" drive receiver or can be used with a 7/8" wrench. Socket will withstand up to 125 lb/ft of torque. 5784 OXYGEN SENSOR SOCKET TOOL 751116 Jims Exhaust pipe retaining ring tool This patent pending installation tool installs the exhaust pipe retaining ring on almost all exhaust system on air cooled Harleys and Buell's from 1984 to present quickly and easily without scratching the exhaust pipe or twisting the ring. 5783 JIMS EXHAUST RETAINING RING TOOL 235804 Race & bearing installation tool 751084 Exhaust gasket Installer Tool This Jims Exhaust Gasket Installer will safely install exhaust gasket seal on air cooled Buells, Evolution Sportster, Evolu‑ tion Big Twin, Twin Cam and Milwaukee Eight evenly and square without distort‑ ing the seal. Without a proper tool, install‑ ing could run the risk of developing an exhaust leak. The tool uses either the two exhaust stud flange nuts from the exhaust system or a JIMS tool handle ZPN235804 to install the seals. Manufactured from high grade 6061 aluminum, and then fin‑ ished with JIMS blue anodizing. 5782 JIMS EXHAUST GASKET INSTALLER TOOL 233144 Exhaust stud drill plate This tool is designed to guide and keep alignment of the drill bit when drilling out broken exhaust studs. A follow up with a tap is all that is needed to clean up thread‑ ed hole. This tool can be used with motor in most frames. Works on Evolution Big Twin 1984‑2000, Twin Cam 1999‑2017, Milwaukee Eight 2017 to present, Evo‑ lution Sportster 1986 to present and air cooled Buell 1987‑2010. 5781 JIMS EXHAUST STUD DRILL PLATE 500411 Speedometer sending unit wrench for all 1994 to present models. Features a 1/4" drive 3/16" ball end Allen bit. The angled design of the wrench allows easy access to the transmission mounted speedometer sending unit. 500405 Exhaust bracket wrench for 1999 thru 2017 Dyna models. Features a shortened and replaceable T‑17 Torx bit. The low profile design allows for easy access to the exhaust bracket in between the frame and the engine. 500407 Oil pressure switch wrench for 1999 to present Touring models. Can also be used for most other 15/16" oil pressure switches. 500406 Lower rocker box wrench for 1994 thru 1999 Evolution Sportster and Big Twin. Has a 7/16" socket that protrudes 1 3/8" (35mm) to reach the application. Special reversible ratcheting wrenches, designed to do a specific job. Feature ergonomic vinyl grips that also prevent from scratching or marring the bike. 5778 SPECIAL WRENCHES STANDARD & UNIVERSAL TOOLS TOOLS & CHEMICALS (Site 1381)
RkJQdWJsaXNoZXIy ODQ0NDEw