www.zodiac.nl 26-027 753612 F lywheel trueness inspection gauge Check flywheel runout of the pinion shaft while assembled in engine case. Also checks the amount of gear lash on aftermarket gear driven cams for Twin Cam engines. By using a JIMS tire rotator ZPN 753615 you can remove most all of the stress being applied to the flywheel by not rotating the engine with the electric starter motor. Kit contains instructions, indicator plate, required hardware and a 1" dial indicator. Works on 1970 thru 1984 Shovelhead, 1984 thru 1999 Evolution Big Twin and 1999 thru 2017 Twin Cam. 5828 JIMS FLYWHEEL RUNOUT INSPECTION GAUGE 751110 For 2002 thru 2017 Twin Cam engines with a Crank Position Sensor 753694 For Milwaukee Eight This Jims tool locks the flywheel in place making certain service procedures easier, such as decompression testing. It is also very visible and useful to designate a bike as decommissioned. The bike will not start, and clutch must be engaged in order to move around the shop. Available for Twin Cam with a Crank Position Sensor, as well as for Milwaukee Eight. 5827'MIGHTY BITE' FLYWHEEL LOCK & DECOMMISSIONED TAG 234996 Crankcase bearing lapping tool (OEM 96710‑40) 235003 Lap head 1.750" (OEM 96718‑58) This crankcase lapping tool aligns left and right main bearing races as well as lapping to size or over‑size on all Sportster, Big Twin and 45 CI motor cases. Comes with 1.375", 1.500" and 1.750" diameter lap heads. Replacement 1.750" lap head is also separately available. 5825 CRANKCASE BEARING LAPPING TOOL Jims Crankcase support block tool for Twin Cam B is an innovative tool designed to protect the left engine case while servicing the inner balancer bearings or performing other general engine work. These blocks attach to the outer side of the engine case underneath the balancer bearing pads surface. The blocks are made of aluminum and have an inserted Delrin pad that rest against the case to prevent marring. The blocks properly support the case, keeping it on a level plane when using a press for bearing service work. These tool blocks also keep the case level when using JIMS tool ZPN751085 to remove the balancer bearings without an arbor press. Comes complete with instruction sheet. 5826 JIMS TWIN CAM B CRANKCASE SUPPORT BLOCK TOOL 751087 Jims Twin Cam B crankcase support block tool 236213 For use on Big Twins 1954 thru early 1981, 1 5/16" socket with 1/2" drive 236216 For use on Big Twins 1972 to present, 1 5/8" socket with 3/4" drive 236215 For use on Big Twins late 1981 thru 1989, 1 1/4" socket with 1/2" drive 236214 For use on Big Twins late 1983 to present, 1 1/2" socket with 1/2" drive 236217 For use on Sportsters 1981 to present, 1 3/8" socket with 1/2" drive Look no further for the best flywheel rebuilding sockets available. Zodiac offers these low‑profile flywheel sockets, which are just long enough to give 100% nut to sprocket contact and 100% drive end contact. Machined flat at the nut receiving end to eliminate rounding off the nut and greatly reducing the risk of bodily injury. These sockets are machined from solid steel 4130 chromium‑molybdenum and heat treated to give a lifetime of service. Available in various models for use on Big Twin models from 1954 to present and Sportster models from 1981 to present. 5824 JIMS FLYWHEEL SOCKETS 782003 Replacement pointer 782002 Replacement adapter for Big Twin models 782001 Replacement adapter for Sportster models 782004 Replacement degree wheel and main adapter assembly 782000 Complete S&S degree wheel kit Multipurpose degree wheel can be used to do ignition timing, crankcase breather timing, cam degreeing, or you name it. Designed to fit the sprocket shaft of any Big Twin or Harley‑Davidson Sportster model simply by using the correct adapter provided. Each kit also comes with a pointer which is held in place with the center crankcase bolt. 5823 S&S DEGREE WHEEL KIT 500410 Crankshaft rotating wrench This 24 tooth ratcheting wrench is used to rotate the crankshaft during engine timing or clearance checks on 2006 thru 2017 Dyna's, 2007 to present Softails and Touring models. Wrench features a non‑slip rubber grip. 5822 CRANKSHAFT ROTATING WRENCH 723120 Sportster engine stand Can be used for engine repair but also as a show stand for all Sportsters 1957 to present. Rugged steel construction with a strong painted finish. 5821 SPORTSTER ENGINE STAND 753695 Milwaukee Eight Touring & Trike engine stand 756310 Milwaukee Eight Softail engine stand Work stand for Milwaukee Eight engines. Blue powder coated .125" steel 5818 JIMS ENGINE STAND FOR MILWAUKEE EIGHT LOWER END TOOLS TOOLS & CHEMICALS (Site 1385)
RkJQdWJsaXNoZXIy ODQ0NDEw