Zodiac Bikers Book by BMG

www.zodiac.nl 26-031 750312 J im's balancer shaft alignment tool This tool is a must have for maintaining a long life of your balancer drive chains and bearings. When using this tool there is no need for guessing for alignment because it will take all the guess work out of setting up your sprocket and chain alignment on a Twin Cam "B" engine. 5864 JIMS TWIN CAM "B" BALANCER SHAFT ALIGNMENT TOOL 750698 Jims crankcase splitter tool Use this tool to "break" the case sealant by pushing apart both crankcase halves. You just bolt the tool with the supplied hardware to the primary mounting holes. Thread‑in the pushing screw by hand and the case will come part and flywheels will be pushed from the left case. No impact tools needed. Works on 2006 Dyna Twin Cam and all Twin Cam 2007 thru 2017. 5862 JIMS CASE SPLITTER TOOL FOR TWIN CAM 750701 Twin Cam case boring tool An easy to use tool that allow you to bore 2006 Dyna Twin Cam and all 2007 thru 2017 Twin Cam crankcases on a heavy‑duty 16" drill press to accept up‑to 4 1/8" bore cylinders. 5863 JIMS CASE BORING TOOL 720492 Crank shaft bushing tool This Jims tool will remove and install crankshaft bushings in the support plate on Twin Cam models. Piloted for accurate operation. 5861 JIMS CRANK SHAFT BUSHING TOOL FOR TWIN CAM 753685 Works on 2017 to present Milwaukee Eight engines in Touring and Trike models Used to hold the two halves of the spring loaded balancer gear in alignment before removal for easy installation. Brightly colored to remind you that you have to remove it before sealing the engine case. 5859 MILWAUKEE EIGHT BALANCER SCISSOR GEAR TOOL 750311 Jims balancer shaft retention pins This tool is developed to secure the engine balancers on Twin Cam "B" engines when servicing the flywheel assembly This tool locks into the balancer's sprocket pin holes to prevent the balancer from turning out of synchronization with the flywheel. 5858 JIMS BALANCER SHAFT RETENTION PINS FOR TWIN CAM "B" 233200 Hard end cap This hard cap protects the sprocket shaft when working on the engine, must be used when working with our crank assembly removing tool (ZPN237337). Works with all 1955 thru 1999 Big Twin and 1999 thru 2006 Twin Cam, except 2006 Dyna. 5856 JIMS SPROCKET SHAFT HARD CAP 720534 Jims Twin Cam crankshaft guide This tool will spread the crankcase pinion bearing rollers while re‑assembling the right side engine case on to the flywheel assembly of any Twin Cam 1999 thru 2017 and 2003 thru 2010 air colled Buell. 5855 JIMS TWIN CAM CRANKSHAFT GUIDE 235850 Jims pinion bushing line reamer tool (OEM 94805‑57) The finest line reamer available, used to line pinion bushing in cam cover from right case race in 1954 thru 1999 single cam Big Twin and the idler gear bushing on 1957 thru early 1984 Sportster. 5854 JIMS PINION BUSHING LINE REAMER TOOL 753684 Works on 2017 to present Milwaukee Eight engines in Touring and Trike models Allows for a perfect installation without removal of the alternator stator including bottoming out when the sprocket shaft seal is in the correct position. 5853 MILWAUKEE EIGHT SPROCKET SHAFT SEAL INSTALLER LOWER END TOOLS TOOLS & CHEMICALS 5860 JIMS BALANCER BEARING TOOLS FOR MILWAUKEE EIGHT The Milwaukee Eight engine in 2017 to present Touring & Trike and 2018 to present Softail incorporates balancers to reduce vibrations. Incorrect installation of the balancer bearings can cause severe damage to the crankcase or even complete engine failure. 756309 Tool to remove the balancer bearings without damage to the crankcase 756306 Installer tool precisely mounts the balancer bearings in the proper location via case bolt and dowel locations without using a driver or press (Site 1389)

RkJQdWJsaXNoZXIy ODQ0NDEw