26-038 26 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 HELMETS & AUDIO PRIMARY & CLUTCH CONTROL CABLES & HYDRAULIC LINES OIL, OIL FILTERS & OIL COOLERS SEAT TRANSMISSION FOOT CONTROLS HARDWARE EXHAUST GASKET & SEALS FRONT FORKS WINDSHIELD ELECTRIC & LIGHT FINAL DRIVE FRAME & REAR SUSPENSION LUGGAGE ENGINE ELECTRICS WHEELS & TIRES FENDER & STRUTS TOOLS & CHEMICALS INTAKE BRAKE GAS- & OIL TANK TECH TIPS & CROSS REF OEM>ZPN ENGINE HANDLEBAR, HAND CONTROLS & MIRRORS GAUGES & DASHES ALPHABETICAL INDEX 751117 J ims tappet adjustment tool This patent pending hand tool simplifies the way to verify proper tappet adjustment. After adjusting the tappet, simply insert the tip of this tool under the hydraulic unit retaining clip, above the pushrod seat. In fact it is a "Go‑or‑no‑go gauge", if the tip doesn't fit between the clip and the pushrod seat or when there is up and down end play, then the tappet is out of adjustment. Only when the tip fits nicely with no end play then the tappet is adjusted properly. Works on all hydraulic tappets except Jims Hydrosolids or hydraulic tappet with travel limiters installed. 5941 JIMS TAPPET ADJUSTMENT TOOL 788735 Valve cover wrench (OEM 11806‑31, 94521‑31) Wrench to remove and install the valve covers on all 45CI Sidevalve engines used in Solo and Servicar models 1931‑1973. 27127 VALVE COVER WRENCH FOR 45CI MODELS 750322 P ushrod cover seal seat cutter Use to correct any misalignment with pushrod cover O‑ring seats when pushrod covers refuse to seal. Works with Evolution Big Twins 1984 thru 1999 and Sportster 1986 thru 1990. Instructions included. 5939 JIMS PUSHROD COVER SEAL SEAT CUTTER Use to check the alignment of the cam bearing to the cam cover bushing to well within .0003" of center line. Any binding of this tool indicates misalignment of cam cover, and or bushing. A must for engine builders. Use on Big Twins from 1970 thru 1999. 5937 JIMS CAM BEARING & BUSHING ALIGNMENT TOOL This tool is the first on the market to re‑ move and install the cam seal on 1970 thru 1984 Shovelhead and 1984 thru 1999 Evolution Big Twins without removing the cam cover. Tool can also be used to remove the cam cover from the crankcase. Does NOT work on Twin Cam models. 5936 JIMS CAM SEAL REMOVER AND INSTALLER TOOL 235795 Jims line reamer tool for Big Twin cam bushings High quality tool to line ream the cam cover bushing of Big Twin models from 1970 thru 1999. 5938 JIMS LINE REAMER TOOL FOR BIG TWIN CAM BUSHINGS 239481 Bearing & Bushing Alignment tool 235994 Cam seal remover & installer tool 753681 Works on 2017 to present Milwaukee Eight engines in Touring, Softail & Trike Precision tool for installation or removal of the camshaft bearing. Holds tighter tolerances and simply works easier than the OEM tool. Features a new removal hole that also works as a window to let you see what you are doing. 5935 MILWAUKEE EIGHT CAMSHAFT BEARING TOOL 751094 Inner cam bearing installer tool This tool is used to install the two inner cam needle bearings on all Twin Cam engines. It perfectly aligns to the shaft bores for a precision press fit. Designed to press from the letter side of the inner cam bearing to eliminate any damage to the bearing, cam or case. Will set bearings .023" to .028" (0.58mm to 0.071mm) below case surface. 5934 JIMS INNER CAM BEARING INSTALLER TOOLS FOR ALL TWIN CAMS 239476 Jims inner cam bearing installation tool This tool installs the inner cam bearing to the proper depth. Can be used on all single cam Big Twin engines from 1958 thru 1999. 5933 JIMS INNER CAM BEARING INSTALLATION TOOL 239475 Jims pinion gear lock tool for 1936 thru 1999 single cam Big Twin Use to lock pinion gear, necessary to torque the pinion nut. Tool is simple to use, just align under‑neath gear and screw into case. Use ZPN234994 to tighten pinion nut. 5932 JIMS PINION GEAR LOCK TOOL 721539 Cam cover holding tool for Big Twin 1970 thru 1999 This handy fixture is easily mounted in a vise, and is used when installing or removing the cam cover bushings on Shovelhead and Evolution Big Twins 1970 thru 1999. It holds the cam cover in a flat position and keeps it from being scratched (not Twin Cam). 5931 CAM COVER HOLDING TOOL 721540 Cam gear alignment tool 1970 thru 1999 single cam Big Twins Another high precision tool from Jims. Designed to index the cam gear's position while removing or installing the cam gear on cam shafts used in 1970 thru 1999 single cam Big Twins. When the cam gear is removed, the gear can be repositioned to another camshaft in exactly the same spot. It is also possible to press the gear on in the advanced or retarded position. Easy to use, time saving and accurate. Use ZPN741904 to remove. 5929 JIMS CAM GEAR ALIGNMENT TOOL TOOLS & CHEMICALS VALVE TRAIN TOOLS (Site 1396)
RkJQdWJsaXNoZXIy ODQ0NDEw