26-050 26 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 HELMETS & AUDIO PRIMARY & CLUTCH CONTROL CABLES & HYDRAULIC LINES OIL, OIL FILTERS & OIL COOLERS SEAT TRANSMISSION FOOT CONTROLS HARDWARE EXHAUST GASKET & SEALS FRONT FORKS WINDSHIELD ELECTRIC & LIGHT FINAL DRIVE FRAME & REAR SUSPENSION LUGGAGE ENGINE ELECTRICS WHEELS & TIRES FENDER & STRUTS TOOLS & CHEMICALS INTAKE BRAKE GAS- & OIL TANK TECH TIPS & CROSS REF OEM>ZPN ENGINE HANDLEBAR, HAND CONTROLS & MIRRORS GAUGES & DASHES ALPHABETICAL INDEX 740294 A xle hex adapter Indian 14mm x 16mm This 14x16mm axle adapter is designed to make it easy to remove the front wheel on Indian Chief, Chieftain, Scout and Roadmaster models. Machined from high‑strength steel. Compact size for easy storage on the bike. 6070 CRUZTOOLS AXLE HEX ADAPTER FOR INDIAN 751070 Plug set for hollow axles Hollow wheel axles are on Buells since 2003 and Dyna and Sportster models 2008 to present. The use of hollow axles has eliminated the center point of the axle, a point that has always been pre‑ ferred for wheel alignment. When you insert this tool in the ends of the hollow axle you have a correct center point again. 6069 JIMS HOLLOW AXLE PLUG TOOL 751088 Jims rear axle nut torque adapter This Jims tool will make adjusting the drive belt tension or rear wheel alignment a bit easier. It will save you time by elimi‑ nating the need to remove the mufflers to perform this service. The tool is designed with a 1/2" drive receiver hole for insert‑ ing your torque wrench thus letting you torque the axle nut from an offset posi‑ tion. Comes complete with instruction sheet. 6068 JIMS REAR AXLE NUT TORQUE ADAPTER 751072 3rd hand axle locker tool Torquing down the rear axle nut on all 2002 to present FLH/FLT models, for ex‑ ample after rear belt adjustment, the welded axle nut tends to move to the low side of the adjuster cam. This movement will allow the belt to loose adjustment. With this 3rd hand axle tool you are able to lock the axle without the assistance of any helper. This tool holds the nut without having to reach around the rear tire to hold the nut from moving. Simply place the 3rd hand over the welded nut on the left‑hand side of the motorcycle. With the neck portion of the tool resting over the swingarm, hand tighten the ad‑ juster screw to take up any slack in tool. Torque the axle nut from the right‑hand side knowing that the welded nut will not turn. Instructions are included. 6067 JIMS 3RD HAND FLH/FLT REAR AXLE LOCKER TOOL 751071 Rear wheel alignment tool Proper wheel alignment is necessary for safe handling of the motorcycle. It will also extend the life of the belt or chain, pulleys and sprockets. With this tool you can simply and accurately obtain the cor‑ rect alignment. In combination with hol‑ low axle plug ZPN751070 this rear wheel alignment tool suits the new hollow axles as found on 2003 to present Buells and 2008 to present Dyna and Sportster models. 6066 JIMS REAR WHEEL ALIGNMENT TOOL 751078 Rear wheel compensator bearing remover and installer. Use this tool to remove and install the compensator ball bearing, after the rear pulley is removed from the rear wheel drive bowl on 2008 to present V‑Rod, Sportster and Touring models. This ball bearing is now positioned with the rubber isolators in the drive bowl. This tool will center and guide the installer plug with the center of the pulley for safe bearing removal and installation. 6065 REAR WHEEL COMPENSATOR BEARING REMOVER AND INSTALLER TOOL 781100 Wheel bearing wrench (OEM 94630‑67) Removes the slotted lock nuts on 1967 thru 1972 spoke wheels. 6064 WHEEL BEARING WRENCH 740047 Colony USA made T‑bar wheel lug wrench (OEM 94621‑35) 780115 Samwel European made T‑bar wheel lug wrench (OEM 94621‑35) 781107 V‑Twin Mfg. 1/2" drive socket Wrenches for the allen head wheel lug bolts as found on all 1935 thru 1972 models. 6063 WHEEL LUG WRENCHES 781103 Wheel bearing puller & installer Removes and installs the wheel bearings on most 2000 to present models with sealed wheel bearings and 3/4", 25mm or 1" axles. 6062 WHEEL BEARING PULLER & INSTALLER 753646 Hub protector for 2014 to present Indian 753621 Tool support plate for 5‑ and 7‑lug cast wheels 741912 Wheel bearing installer & remover kit for 3/4", 1" and 25mm axles 751077 Optional bearing installer & bearing puller for 25mm axle Use to remove and install "new style" sealed wheel bearings, as used in both ABS and non‑ABS equipped 2000 to present Harley‑Davidson, Buell and 2014 to present Indian models, without damaging the wheel. The kit is used for bearings for 3/4", 1" as well as 25mm axles. Kits supplied before 2007 did not include the tools for 25mm but can be upgraded with the optional bearing installer and bearing puller kit. For the cast 5‑ and 7‑lug wheels in 2010 to present CVO's and all 2014 to present Touring a tool support plate must be ordered separately. For 2014 to present Indian a hub protector must be ordered separately. 6061 JIMS WHEEL BEARING REMOVER AND INSTALLER KIT FOR 2000 TO PRESENT MODELS 237107 Spacer driver tool The effectiveness of any bearing race remover tool is dependent on the ability to grip the race. This spacer applies outward force on the bearing race tool to allow easier removal. Must be used with handle ZPN235804. Works with most Jims bearing race tools, such as ZPN233171, 237351 and 235921. 6060 JIMS TOOL DRIVER SPACER TOOLS & CHEMICALS WHEEL & TIRE TOOLS (Site 1408)
RkJQdWJsaXNoZXIy ODQ0NDEw