www.zodiac.nl 03-096 PRIMARY & CLUTCH CONTROL CABLES & HYDRAULIC LINES OIL, OIL FILTERS & OIL COOLERS SEAT TRANSMISSION FOOT CONTROLS HARDWARE EXHAUST GASKET & SEALS FRONT FORKS WINDSHIELD ELECTRIC & LIGHT FINAL DRIVE FRAME & REAR SUSPENSION LUGGAGE ENGINE ELECTRICS WHEELS & TIRES FENDER & STRUTS TOOLS & CHEMICALS INTAKE BRAKE GAS- & OIL TANK TECH TIPS & CROSS REF OEM>ZPN ENGINE HANDLEBAR, HAND CONTROLS & MIRRORS GAUGES & DASHES ALPHABETICAL INDEX HELMETS, LUGGAGE, AUDIO & MORE 32664 OXYGEN SENSOR SOCKET TOOL This tool is used to remove or install the oxygen sensor on all FLH and FLT series Touring models 2006 thru 2009, Softail, Dyna and V-Rod 2006 thru 2011, 2007 to present Sportster and closed loop fuel injected Buell models. Socket has a 3/8" drive receiver or can be used with a 7/8" wrench. Socket will withstand up to 125 lb/ft of torque. 751055 Fits all unheated Fuel Injected Oxygen Sensor equipped models 2006-present 30969 O2 SENSOR FOR BUELL Stock replacement for the since long obsolete O2 sensor for 1999-2002 Buell X1 and 1999-2002 Buell S3. 747585 Buell O2 sensor, Cycle Pro (OEM 65970-99Y) 8679 WELDON O2 SENSOR BUNG Steel weld-on bung for M18 x 1.5 threaded Wideband O2 sensors and socket plugs to close off when no O2 sensor is fitted. 741993 Weld-on nut for exhaust oxygen sensor, each 741994 Socket plug for weld-on nut, each 27878 O2 SENSOR ADAPTER INSERT Insert allows the installation of a 3-wire heated and M12x1.25 threaded O2 sensor in a M18x1.5 threaded bung for a wide band O2 sensor. 758590 O2 sensor adapter insert, each 634 WELDIN SENSOR BUNGS Accessory weld-in 18mm sensor bungs with cap for exhaust systems that have 12mm sensor bungs or no sensor bungs at all. A must when installing a ThunderMax Fuel Injection or other Fuel Injection system or tuner that requires the use of Wide-Band Oxygen sensors. Sold each. 723236 Straight 18mm weld-in sensor bung 723237 Angled 18mm weld-in sensor bung 633 O2 SENSOR BUNG PLUGS AND ADAPTERS 783403 Sensor bung adapter plugs, M18x1.50 to M12x1.25, pair 735750 Sensor bung plugs, M18 x1.5, pair 783402 Sensor bung plugs, M12x1.25 with 17mm hex head, pair 783404 Sensor bung plugs, M10x1.25 with 1/2” hex head, pair Daytona Twin-Tec 742043 Fits 2006-2011 models with unheated M18 threaded O2 sensors 742044 Fits 2012 to present Softail, 2010 to present Touring & Trike, 2012-2017 Dyna and 2007-2013 Sportster with 4-wire heated M14 threaded O2 sensors, including Euro-5 rear sensors 742068 Fits 2014 to present XL Sportster with 4-wire heated M14 threaded O2 sensors 1688 OXYGEN SENSOR ELIMINATOR KITS These O2 sensor eliminator kits are used when you want your bike to run without O2 sensors, for example when you want to change air/fuel ratio at idle and part throttle for racing applications using Diag4Bike, Daytona Twin Tec Twin Tuners in conjunction with a Daytona Twin Scan Tool, Dynojet Power Commander, Screamin' Eagle Pro Super Tuner and similar. The eliminators plug into the stock wiring harness and simulate a cold sensor condition, causing the ECM to remain in "open-loop" operation. Eliminators for 4-wire heated sensors can also be used to eliminate the secondary O2 sensors on Euro-5 motorcycles but then their only function is to keep moisture and dirt out of the wiring side connectors to keep them intact for later use. Related CEL (Check Engine Light) and DTC's (Digital Trouble Codes) can be disabled with Diag4Bike software and a Diag4Bike Tuning License. Zodiac European made 744444 Fits 2012 to present Softail, 2010 to present Touring & Trike, 2012-2017 Dyna and 2007-2013 Sportster with 4-wire heated M14 threaded O2 sensors, including Euro-5 rear sensors 1687 POWER COMMANDER O2 SENSOR ELIMINATORS These O2 sensor eliminators are the same as supplied with some Dynojet Power Commanders but can also be used when you want your bike to run without O2 sensors. They plug into the stock wiring harness to avoid that warning light coming up or fault codes appearing on your instruments. Fits 2007 thru 2011 models with unheated M18 threaded O2 sensors. Sold each. 712023 O2 sensor eliminator 632 RETROFIT OXYGEN SENSOR EXTENSION HARNESS NAMZ produces these kits for those who want to fit an aftermarket exhaust system designed for a 2009 FLH or FLT onto a 2010 or later FLH or FLT series Touring model, or from their 2007 thru 2011 Softail or Dyna onto a 2012 to present Softail or Dyna. O2 sensors on the later models are much further back on the head pipe and the O2 sensors are smaller in diameter as on older models. These kits include two 18mm to 12mm O2 bung adaptors and a harness extension to retrofit older exhausts on the later models. The Plug-N-Play kit comes with the wiring connectors installed, the economy kit only has the wire terminals installed and must be used with the OEM connectors. 701677 Plug-N-Play O2 retrofit kit 701678 Economy O2 retrofit kit EXHAUST Exhaust Accessories
RkJQdWJsaXNoZXIy ODQ0NDEw