www.zodiac.nl 04-020 PRIMARY & CLUTCH CONTROL CABLES & HYDRAULIC LINES OIL, OIL FILTERS & OIL COOLERS SEAT TRANSMISSION FOOT CONTROLS HARDWARE EXHAUST GASKET & SEALS FRONT FORKS WINDSHIELD ELECTRIC & LIGHT FINAL DRIVE FRAME & REAR SUSPENSION LUGGAGE ENGINE ELECTRICS WHEELS & TIRES FENDER & STRUTS TOOLS & CHEMICALS INTAKE BRAKE GAS- & OIL TANK TECH TIPS & CROSS REF OEM>ZPN ENGINE HANDLEBAR, HAND CONTROLS & MIRRORS GAUGES & DASHES ALPHABETICAL INDEX HELMETS, LUGGAGE, AUDIO & MORE µ ´ 27567 RICK'S BAR END TURN SIGNALS FOR SPORTSTER S Billet aluminum brackets to be fitted on the handlebar ends. Wiring for the turn signals can be routed through the handlebars. Brackets also allow you to fit your mirrors on the handlebar ends. Fits 2021 to present RH1250S Sportster S 757583 Left & right bracket kit complete with E-approved Kellermann Atto turn signals and matching Load Equalizing resistors 772 KELLERMANN "STEALTH" OX EYE HANDLEBAR TURN SIGNALS State of the art design handlebar turn signals that look like "ordinary" end stops when not in use. In one word; Stealth. They feature a circular dark tinted lens with high power LED technology that shines in bright amber when activated. Installation requires -except for models with a CAN-Bus system-, the use of an electronic turn signal flasher unit such as the ZPN237304 or two Kellermann in-line resistors ZPN742046 to retain the original flashing sequence. Resistors as well as turn signals are sold each. 742095 Kellermann BL-2000 "Stealth", chrome, each 742045 Kellermann BL-2000 "Stealth", black, each 742046 Turn signal resistor, 7.5 Ohms 32880 RICK'S ATTO FRONT TURN SIGNALS FOR LOWRIDER ST These black anodized aluminum housings feature E-approved Kellermann Atto turn signals. They bolt straight onto the OEMfairing bracket of Softail Low Rider ST and El Diablo. Strongly recommended to install together with Kellermann's i.Load load equalizer. 770133 Rick's Atto front turn signals for 2022 to present FXLRST and FXRST, pair 34144 KELLERMANN "DASH" FRONT TURN SIGNALS Kellermann "Dash" turn signals are sensationally small and fit straight under your handlebar controls, almost invincible when turned off but spectacularly bright when turned on. They feature EXtranz - Extreme Optical Transparency and Kellermann HighPower LED Technology. The aluminum body has a black finish and is pre-wired. Fits 2018 to present Softail 745442 Dash A single turn signal, front left 745443 Dash A single turn signal, front right 745444 Dash M triple turn signal, front left 745445 Dash M triple turn signal, front right Turn-brake-tail combination light 743827 Atto DF Integral, clear lens, amber turn signal, red tail and brake light, each Tail & brake light combination 743828 Atto RB Integral rear and brake light, clear lens, red light, each 743829 Atto RB Dark Integral rear and brake light, dark lens, red light, each Turn signals 743825 Atto Integral turn signal, clear lens, amber light, each 743826 Atto Dark Integral turn signal, dark lens, amber light, each 6980 KELLERMANN ATTO INTEGRAL TURN SIGNAL & RUNTURNBRAKE LIGHTS Kellermann's popular Atto LED lights are also available as build-in units. With a lens diameter of just 8.9mm and 13mm length (16mm for the DF) these can be installed virtually anywhere, and with an input of between 1, 5W to 3W they hardly require any power from the battery at all. Spot accessories 743849 Black mounting plates to fit Atto's or Spots to Harley handebar controls, set of 2 743840 Chrome mounting plates to fit Atto's or Spots to Harley handebar controls, set of 2 743846 Mounting extension, 15mm long, each 743839 Offset mounting plates, black, pair 743845 Black adapter nut, 20mm long, M8 external to M5 internal, each 743844 Black adapter nut, 40mm long, M8 external to M5 internal, each 743843 Black adapter nut, 20mm long, M10x1.25 external to M5 internal, each 743841 Strip to fit Atto's or Spots on license plate mounts, 174mm wide, each 743842 Strip to fit Atto's or Spots on license plate mounts, 204mm wide, each 743947 Spot Tail/Brake light, clear lens, red leds, each 743948 Spot Tail/Brake light, smoke lens, red leds, each This innovative combination of turn signals with integrated taillight function is now united in the Micro 1000 housing. Due to the integration of the taillight functions in the turn signals you do not need a taillight in the center of the bike anymore. This will give your bike a totally new appearance. The Micro 1000 DF replaces turn signals and the taillight and are EU-approved for the rear. They feature Kellermann's High Power LED-Technology with a current draw of only 1 Watt for taillight and 1 Watt for brake light. These LED's are built into a high quality steel housing. Unit measures approx. 72mm length (w/o thread), 18mm height and 17mm depth, with a lens size of only 44mm x 15,5mm. These turn/tail lights have replaceable M8- threaded anti-vibration adapters which protect from damage due to vibrations or vandalism. Installation requires the use of a ZPN742048 resistor for the taillight function, one ZPN742046 resistor for the brake light function, and -except for models with a CAN-Bus system-, the use of an electronic turn signal flasher unit such as the ZPN237304 or two Kellermann in-line resistors ZPN742046 to retain the original flashing sequence. Resistors as well as turn signal/taillight combinations are sold each. 777 KELLERMANN MICRO 1000 DF TURN/ TAIL LIGHTS ELECTRIC & LIGHT Turn Signals & Multi Function Lights
RkJQdWJsaXNoZXIy ODQ0NDEw