07-066 HELMETS & AUDIO PRIMARY & CLUTCH CONTROL CABLES & HYDRAULIC LINES OIL, OIL FILTERS & OIL COOLERS SEAT TRANSMISSION FOOT CONTROLS HARDWARE EXHAUST GASKET & SEALS FRONT FORKS WINDSHIELD ELECTRIC & LIGHT FINAL DRIVE FRAME & REAR SUSPENSION LUGGAGE ENGINE ELECTRICS WHEELS & TIRES FENDER & STRUTS TOOLS & CHEMICALS INTAKE BRAKE GAS & OIL TANK TECH TIPS & CROSS REF OEM>ZPN ENGINE HANDLEBAR, HAND CONTROLS & MIRRORS GAUGES & DASHES ALPHABETICAL INDEX 627TC The 627 employs valve train stability improvements for greater performance and reliability. This results in a flat torque curve with great top end power. This cam is a real powerhouse in a 103-117" engine with high compression and good flowing heads. Available for roller chain drive only. 723289 Fits 2006 Dyna and all 2007-2017 Twin Cam with roller chain cam drive 577TC Performance cams for 95"-103" Twin Cam engines. Nice, smooth power and big torque in engines with good flowing heads, increased compression (9.5-10.5: 1), performance ignition, exhaust and larger carb or throttle body. Bolt-in with conical springs or CVO 103 heads; runs very quiet. Can produce 105-110 rear wheel HP and torque in 95" engines. 723282 Fits 1999 thru 2006 Twin Cam with Silent Chain cam drive (except 2006 Dyna) 723281 Fits 1999 thru 2006 Twin Cam with S&S Gear Drive (except 2006 Dyna) 723283 Fits 2006 Dyna and all 2007-2017 Twin Cam with roller chain cam drive 723284 Fits 2006 Dyna and all 2007-2017 Twin Cam with S&S Gear Drive 575TC Torque cams specifically designed for CVO 103" engines. Best choice for riders who want a large increase in useable torque with durability and smooth, quiet operation. Creates best power between 2000-4800 rpm for a strong pull you will enjoy with every shift. Bolt-in with CVO 103 heads or conical springs. Spring spacing required on 1999 thru 2004 models. 723286 Fits 1999 thru 2006 Twin Cam with Silent Chain cam drive (except 2006 Dyna) 723285 Fits 1999 thru 2006 Twin Cam with S&S Gear Drive (except 2006 Dyna) 723287 Fits 2006 Dyna and all 2007-2017 Twin Cam with roller chain cam drive 723288 Fits 2006 Dyna and all 2007-2017 Twin Cam with S&S Gear Drive 557TC Bolt-in cams for 88 thru 110 inch engines with stock, unmodified heads. Lowers engine temperatures, increases torque and horsepower across the board, with emphasis on torque. Spring spacing required on 1999 thru 2004 models. 723279 Fits 1999 thru 2006 Twin Cam with Silent Chain cam drive (except 2006 Dyna) 723278 Fits 1999 thru 2006 Twin Cam with S&S Gear Drive (except 2006 Dyna) ThunderMax Cams by Red Shift are designed to deliver unmatched performance and smooth, linear power with great valve train dynamics. ThunderMax cams are ground from one-piece 8620 steel billets utilizing the latest manufacturing techniques. Available in standard splined gear chain drive, or configured for use with S&S Gear-Drive gear sets. Red Shift recommends new cam bearings and performance tappets with any cam change. All ThunderMax cams require adjustable pushrods; spring work required unless otherwise noted as a bolt-in cam. Gear drive camshafts are supplied as a cam-only kit with front and rear cams only. For cam drive gears, as well as required gaskets, bearings and other hardware, see below. Notes: •Make sure you select the right cam for the job. Increasing compression ratio and/or displacement beyond the recommended range for each cam will increase cylinder pressure, which makes the engine harder to start and more likely to ping or detonate. Lower compression ratios or displacements will weaken performance at low and mid range RPM. •A hydraulic press and other professional tools are required to install cams in Twin Cam engines. Additionally, material must be removed from the inner surface of the stock gear cover to install the S&S Gear Drive. •New cam bearings and a new gear cover gasket are required to complete this installation. These parts are provided in the Camshaft Installation support kit. If updating from the stock Silent Chain drive system on 1999 thru 2006 models (except 2006 Dyna), order 1 set cams, 1 cam gear drive kit ZPN721948 and a Camshaft Installation Support kit ZPN721950 •If updating from the stock roller chain drive system on 2006 Dyna or any 2007-2017 Twin Cam model, order 1 set cams, 1 cam gear drive kit ZPN750871 and a Camshaft Installation Support kit ZPN750873 •Due to the characteristics of gear drives, you may experience some valve train noise. 2059 THUNDERMAX CAMS BY RED SHIFT FOR TWIN CAM (Ȧ*ȡ1ȝ CAMS FOR TWIN CAM (Site 476)
RkJQdWJsaXNoZXIy ODQ0NDEw