www.zodiac.nl 07-075 Washers in 5 packs 232677 .050" (OEM 25550-36 232678 .055" (OEM 25551-36) 232679 .060" (OEM 25552-36) 232680 .065" (OEM 25553-36) 232681 .070" (OEM 25554-36) 232682 .075" (OEM 25555-36) 232683 .080" (OEM 25556-79) 232684 .085" (OEM 25557-79) 232685 .090" (OEM 25558-79) 232686 .095" (OEM 25559-79) 232687 .100" (not included in assortment kit) 232675 Assortment washer kit 10 sizes Precision thickness spacing washers will enable you to properly adjust camshaft end play on Big Twins from 1936 to present, including Evolution motors. These are available in thickness from .050" to .95" in .005" increments. An assortment package of one of each thickness is offered, along with each thickness available individually in 5 packs. 2091 CAM GEAR SPACING WASHERS 233511 Cam shims (OEM 6769) 233512 Cam shims + .005 (OEM 6770) A must when setting up new cams. Fits 1957 thru 1985 Sportster engines. Sold in packs of 10. 2090 SPORTSTER CAM SHIMS 235998 Staking pins (10 pack) Simple, but effective. These pins can be used on all bushings and will hold the bushing in place. Use with the bushing installers drilling jigs, as found elsewhere in this catalog. The staking pins are sold in a 10 pack (OEM 275). 2089 STAKING PIN FOR STAKING BUSHINGS 235929 Cam bearing gauge, set Inner cam needle bearing "Go and No Go" gauge. The only accurate and easy way to check the size of the inside diameter of your inner cam bearing. Use these pins to check if your cam is too tight or too loose. Sold in a set of two and used on all single cam Big Twin models from 1958 thru 1999. 2088 JIMS CAM NEEDLE BEARING GAUGE 741899 Jims pinion gear spacer (OEM 24703-54B) Quality replacement spacer for stock or aftermarket engines. For use on 1954 thru 1989 Big Twin models. 2084 JIMS PINION GEAR SPACER 750559 V-Rod cam followers, 8-pack Made by Kibblewhite Precision Machining for use in V-Rod models with high lift cams installed. Dependent on valve lift custom machining may be required. Fits all 2002-2017 V-Rod models. Sold in sets of 8. 2083 CAM FOLLOWERS FOR VROD 1955-1990 Big Twins 760417 S&S pinion gear spacer (OEM 24703-54B) 741899 Jims pinion gear spacer (OEM 24703-54B) 1991 thru 1992 Big Twins (OEM 24022-90) 235009 Pinion shaft nut L/H thread 1955 thru 1990 Big Twins (OEM 24023-54) 234999 Pinion shaft nut L/H thread Replacement pinion gear shaft spacer and left hand threaded nut for Big Twin models from 1955 thru 1992. Machined with perfection to meet or exceed OEM specifications. 2081 PINION GEAR NUT AND SHAFT SPACER 231488 Fits 1958-1999 Big Twins. Heat treated and precision ground (OEM 25550-57). 2080 CAM THRUST LOCK WASHER 235782 Cam bushing (OEM 25597-36) 235781 Cam bushing +.005" American made crankcase cam bushing for Big Twin 1936 thru 1957. Available in standard and .005" oversize. 2079 JIMS CRANKCASE CAM BUSHING 234460 Time Saver kit 1970 thru 1992 234461 Time Saver kit 1993 thru 1999 These kits save you the hassle of finding the right gaskets, seals and O-rings when changing the cam on Big Twin models 1970 thru 1999. They include nose cone, points cover and tappet block gaskets, nose cone oil seal, and all the right pushrod tube O-rings and/or seals needed. When buying a cam shaft, buy a "Time Saver" kit and you can't go wrong. 2078"TIME SAVER" CAM CHANGE GASKET KIT 231443 Koyo-USA full needle type cam bearing (OEM 9058). Also replaces OEM 9058A 238932 S&S full needle type cam bearing (OEM 9058). Also replaces OEM 9058A These are the full-needle type bearings as used from 1958 thru 1991 and are recommended as a replacement for the 1992 thru 1999 (OEM 9058A) bearing INA SCE 138 USA, which has less needles and consequently a lower load rating. 2077 CAMSHAFT NEEDLE BEARING CAM ACCESSORIES (Ȧ*ȡ1ȝ (Site 485)
RkJQdWJsaXNoZXIy ODQ0NDEw