www.zodiac.nl 08-021 PRIMO BELT DRIVES 3Ȫ,ȥ$Ȫ< &Ȥ8Ȭ&Ƞ Brute IV Brute IV & Brute V & late 1 3/4 Brute III Extreme ø 2 1/2" ø 3 1/2" 700502 721727 Standard insert (NO offset) 700507 700507 Standard motor nut - 721735 3/8" offset insert - 700508 3/8" offset motor nut 700503 721728 1/2" offset insert 700508 700508 1/2" offset motor nut 700504 - 3/4" offset insert 700509 700509 3/4" offset motor nut 700505 721729 1" offset insert 700510 700510 1" offset motor nut - 721730 1 1/4" offset insert - 700511 1 1/4" nut 700506 721731 1 1/2" offset insert 700511 700511 1 1/2" offset motor nut - 721732 2" offset insert - 700511 2" offset motor nut 700512 700512 Special washer for off-set pulleys Brute III 700500 Outside guide for offset pulley insert 700501 Standard insert (NO off-set) 700502 1/2" off-set insert 700507 1/2" off-set motor nut 700503 1" off-set insert 700508 1" off-set motor nut 700504 1 1/4" off-set insert 700509 1 1/4" off-set motor nut 700505 1 1/2" off-set insert 700510 1 1/2" off-set motor nut 700506 2" off-set insert 700511 2" off-set motor nut 700512 Special washer for offset pulleys These Primo offset front pulley inserts allow custom bike builders the freedom to offset the transmission allowing the use of a wider rear wheel-tire assembly. There are two different insert styles available, a 2 1/2" diameter insert to fit Primo Brute III 1 3/4" and early style Brute IV 3" belt pulleys, the other a 3 1/2" diameter insert that fits late style Brute IV 3" wide belt pulleys. All inserts come with 5 countersunk screws and 2 dowel pins. You will need to select an outside guide, an insert and corresponding motor nut and the special washer. 2602 OFFSET FRONT PULLEY INSERTS PRIMO REPLACEMENT BELTS HTD Kevlar/Aramid Teeth Pitch Width Primary Pulley combination/fitment 722972 - 144 8mm 1 1/2" Long 47 x 76 pulley, fits old model belt drive - 700545 132 8mm 1 1/2" Long 39 x 62, 40 x62 ad 41 x 61 pulley, stock belt on ZPN195028, 195004, 195006 & 195000 - 700546 132 8mm 1 1/2" Long .050" longer, use when ZPN700545 is to short - 237504 130 8mm 1 3/4" Short 48 x 68 pulley, fits ZPN237284, 237286, 237288 - 237505 138 8mm 1 3/4" Long 45 x 68 pulley, fits ZPN237285 196056 - 144 8mm 2" Long 47 x 76 & 48 x 76 pulley, fits ZPN195008 196060 - 144 8mm 3" Long 47 x 76 & 48 x 76 pulley, fits ZPN195024, 720350, 720351 237437, 237438, 237441, 721722 - 740127 132 8mm 3" Short 44 x 76 pulley, fits ZPN237435, 237436, 720352, 720353 - 722971 101 11mm 1 3/4" Long 34 x 49 pulley, fits ZPN722544, 722545, 72246, 722547, 722939 & 722959 - 722945 101 11mm 1 1/2" Long 33 x 49 & 34 x 49 pulley, fits ZPN722935, 722936, 722937, 722944 722259 - 85 14mm 3 1/2" Long 30 x 46 pulley, fits ZPN722252, 722253 - 700525 78 14mm 1 1/2" Long 24 x 37 pulley Primo offers replacement belts in two strength. The normal HTD belt replaces the belt that is normally supplied with the Primo belt drive kits. There is also a Kevlar quality belt available. The Kevlar belts feature a kevlar cord layer that has exceptional strength compared the cord layer in the HTD belts. Kevlar belts are highly recommended for use with high performance and big cubic inch motors. Primo Kevlar belts are used on the primary of the 600 + Horsepower Drag-Bikes of Ton Pels and many others. 2601 REPLACEMENT BELTS FOR PRIMO BELT DRIVE KITS (Site 575)
RkJQdWJsaXNoZXIy ODQ0NDEw