www.zodiac.nl 10-035 742498 For S&S HVHP oil pump 1992-1999 Big Twin Metal gaskets with silicone beading plus all other seals, keys, check ball and other hardware to rebuild your oil pump. 2477 JAMES SILICON BEADED METAL GASKET KITS FOR BIG TWIN OIL PUMPS 742402 James Gasket tappet cover seal and screw kit Kit contains O-rings for the upper, middle and lower push rod cover, Silicone beaded SteelCore gaskets for the tappet cover and 8 chrome plated screws with washers for the tappet cover. Fits all 1999 thru 2017 Twin Cam models. 2475 JAMES TAPPET COVER SEAL & SCREW KIT FOR TWIN CAM Big Twin models 233990 Fits 1936 thru 1947 Knuckleheads and FL(H) 233991 Fits 1948 thru 1964 Panhead and 1965-early 1979 Shovelhead 233993 Fits 1979 thru 1981 Shovelhead 233994 Fits 1981 thru 1983 Shovelhead 233995 Fits 1984 thru 1999 Evolution 231522 Fits 1999-2017 Twin Cam, includes tappet block gaskets Sportster models 233990 Fits 1957 to early 1979 Iron Head 233992 Fits 1979 thru 1985 Iron Head 233995 Fits 1986 thru 1990 Evolution 233996 Fits 1991 thru 2003 Evolution 740608 Fits 2004 to present Evolution and Buell, includes tappet block gaskets Each kit includes all seals, washers, o-rings needed when replacing or re-packing the pushrod tubes. Kits are available for Sportster models 1957 to present and Big Twin models 1936 to present including Evolution and Twin Cam models. 2474 PUSHROD SEAL KITS FROM JAMES GASKETS 742483 Inner primary gasket & lock plate This Steel Core gasket is completely molded in rubber with silicon tracers for superior sealing. Comes with lock plate. Fits 1965 Panhead and 1966 thru 1969 Shovelhead. Made by James Gaskets. 2473 JAMES' STEELCORE INNER PRIMARY TO CRANKCASE GASKET 741812 Fits 1948-1965 Panhead & 1966-early 1979 Shovelhead, rubberized cork 741813 Fits 1957-1979 Sportster and 1936-1947 Knucklehead, rubberized cork 741814 Fits 1984-2000 Evolution Big Twin, rubber Kits with four upper seals, four lower seals and four center seals. 2472 PUSHROD COVER SEAL KIT 231961 Seal washer for inner primary bolt OEM 786A, Genuine James, 10-pack 760883 Seal washer for inner primary bolt OEM 786A, Cometic, 10-pack 2006-2017 Dyna, 2007 to present Softail, 2000 to present Touring and 2009 to present Trike models are supplied with a 6 speed transmission and a new primary section. The inner primary on these models is bolted to the transmission and engine with five hex serrated screws with washer. This washer should work as a seal too. Usually this works until the primary is taken off for the first time. 2471 INNER PRIMARY SEAL WASHERS FOR 6 SPEED TWINCAM & MILWAUKEE EIGHT 231237 For use with 1990 thru 1993 inner primary 231238 For use with 1994 thru 2006, except 2006 Dyna Convenient kits with seals, bearings, bushings and lock tabs you need when installing an inner primary on all 1990 thru 1999 Evolution Big Twins and 1999 thru 2006 Twin Cam models, except 2006 Dyna. 2470 INNER PRIMARY MOUNT & SEAL KITS 742450 Clutch release cover gasket Made by James Gaskets. Reinforced metal with Silicone beading. Fits Screamin' Eagle 6-speed transmissions. 2469 CLUTCH RELEASE COVER GASKET FOR SCREAMIN' EAGLE 6SPEED SPECIAL & BIG BORE GASKETS *ș6ȣ(Ȭ 6ȝ$Ȥ6 (Site 721)
RkJQdWJsaXNoZXIy ODQ0NDEw